DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Boxes and organizers · 7 min

Laser Cut Condiment Organizer Files: 12 Free Oil and Sauce Organizers

DXF World team, Makers and editors
Short answer

A laser cut condiment organizer is a plywood tray or box with bays for oil bottles, sauces and spice shakers, joined with tabs and slots. The 12 free files below range from a 7-part, 240 × 120 × 100 mm caddy to a 10-part, 360 × 180 × 90 mm chest with a pin-hinged lid, including two-row organizers, a stepped packet station and a sliding lid box. Each comes in SVG and DXF for 3, 4, 5 and 6 mm plywood and cuts in about 13 to 34 minutes on a 10 W diode (3 mm).

Lift the olive oil bottle and there it is: a sticky ring on the counter, the third one this month, with a few grains of salt glued into it. Every kitchen has a corner where the oil, the vinegar, the soy sauce and three hot sauces live in a loose crowd. A laser cut condiment organizer gives that crowd a home: one bay per bottle, shakers in front, and one tray to lift when you wipe the counter.

Here are 12 oil and sauce organizer files from the DXF World library. They cover slim trays for the back of the counter, two-row organizers for bottles and shakers, a stepped station with slots for sauce packets, and three boxes with lids. Every download has SVG and DXF drawn separately for 3, 4, 5 and 6 mm plywood, the parts join with tabs and slots, and all 20 files are in the oil and condiment organizers category.

Laser cut condiment organizer files compared

FileTypeOuter size, mm (W × D × H)Parts10 W diode, 3 mm
Condiment caddy, 3 sectionsOpen, 120 mm deep240 × 120 × 100713 min 56 s
Slanted oil and sauce trayOpen, sloped front240 × 160 × 80714 min 44 s
Oil and vinegar cruet boxOpen, straight walls260 × 180 × 80719 min 39 s
Long condiment tray, 4 sectionsOpen, single row340 × 120 × 100817 min 25 s
Square oil bottle organizerOpen grid, 2 × 2240 × 240 × 100818 min 48 s
Hot sauce bottle organizer, 6 baysOpen grid, 2 rows290 × 180 × 90826 min 59 s
Tall oil and vinegar organizerOpen, 120 mm tall280 × 220 × 120820 min 9 s
Condiment station, 8 compartmentsOpen grid, 2 rows340 × 200 × 901226 min 22 s
Three-tier sauce and packet organizerStepped tiers300 × 220 × 1001125 min 22 s
Hinged sauce bottle boxLid on plywood pins240 × 180 × 80820 min 53 s
Sliding lid sauce box, 8 sectionsSliding lid on rails340 × 160 × 1001233 min 51 s
Hinged condiment chest, 8 sectionsLid on plywood pins360 × 180 × 901034 min 0 s

Cut times are estimates for the 3 mm file from the cut length. On a 40 W CO2 the same organizers take roughly 5 to 15 minutes. Treat all of them as a starting point and test your settings on scrap.

Slim trays for oil and sauce bottles

The back of a counter is rarely deep. These four stay narrow and keep a few bottles in a tidy line.

Light birch plywood condiment caddy with three sections holding olive oil, soy sauce, ketchup, salt and pepper shakers and herb jars on a kitchen counter by a white brick wallCondiment Caddy, 3 SectionsOuter size (W × D × H) 240 × 120 × 100 mm (9.45 × 4.72 × 3.94 in)Parts 7Est. time, 10 W diode (3 mm) 13 min 56 sEst. time, 40 W CO2 (3 mm) 5 min 48 sSVG · DXF →

Only 120 mm deep and the fastest file in this roundup at 13 min 56 s on a 10 W diode. Three sections for an oil bottle, a sauce and the salt and pepper, with a front only slightly lower than the back.

Light birch plywood tray with three sections and a sloped front on a speckled stone counter, holding small sauce jars, two olive oil bottles and a dark vinegar bottle.Slanted Oil and Sauce Tray, 3 SectionsOuter size (W × D × H) 240 × 160 × 80 mm (9.45 × 6.30 × 3.15 in)Parts 7Est. time, 10 W diode (3 mm) 14 min 44 sEst. time, 40 W CO2 (3 mm) 6 min 08 sSVG · DXF →

Three sections side by side and a front wall lower than the back, so the side panels slope toward you. At 240 × 160 × 80 mm it fits between the hob and the wall where a bigger box would not.

Birch plywood box with three bays on a light wood counter, holding small hot sauce bottles, two olive oil pourers and two corked cruets of oil and vinegar.Oil and Vinegar Cruet Box, 3 BaysOuter size (W × D × H) 260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in)Parts 7Est. time, 10 W diode (3 mm) 19 min 39 sEst. time, 40 W CO2 (3 mm) 8 min 11 sSVG · DXF →

Straight walls all round, no slope, which gives it a calm, classic look on a dining table. Three bays for oil and vinegar cruets, pourer bottles and a small sauce.

Long light birch plywood condiment tray with four sections holding oil, balsamic, ketchup, mustard, salt and pepper shakers, soy sauce and hot sauce on a wooden kitchen tableLong Condiment Tray, 4 SectionsOuter size (W × D × H) 340 × 120 × 100 mm (13.39 × 4.72 × 3.94 in)Parts 8Est. time, 10 W diode (3 mm) 17 min 25 sEst. time, 40 W CO2 (3 mm) 7 min 15 sSVG · DXF →

Four bays in a single row across 340 mm, still only 120 mm deep. Oil, sauce, mustard and a spice shaker line up along the wall. Its layout is about 1284 mm long, so a desktop laser will need a couple of runs.

Pro tip: measure the base of your biggest bottle before you cut. Bottles differ a lot in shape, and a square oil bottle needs a wider bay than a round one of the same volume. Compare it with the section width: box width minus the walls, divided by the number of sections.

Two-row organizers for bottles and shakers

Tall bottles at the back, shakers and small jars at the front: this is the layout that fits most kitchens.

Square light birch plywood organizer with four compartments holding oil, soy sauce, ketchup, hot sauce and two pairs of spice shakers, on a light kitchen counter in front of wood-slat cabinetsSquare Oil Bottle Organizer, 4 SectionsOuter size (W × D × H) 240 × 240 × 100 mm (9.45 × 9.45 × 3.94 in)Parts 8Est. time, 10 W diode (3 mm) 18 min 48 sEst. time, 40 W CO2 (3 mm) 7 min 50 sSVG · DXF →

A square 240 × 240 × 100 mm box with a 2 × 2 grid: bottles at the back, spice shakers at the front. A square shape fits a corner of the counter better than a long tray.

Open birch plywood organizer with six bays on a pink kitchen counter, oil and soy sauce bottles in the back row and groups of small hot sauce and dressing bottles in front.Hot Sauce Bottle Organizer, 6 BaysOuter size (W × D × H) 290 × 180 × 90 mm (11.42 × 7.09 × 3.54 in)Parts 8Est. time, 10 W diode (3 mm) 26 min 59 sEst. time, 40 W CO2 (3 mm) 11 min 14 sSVG · DXF →

Six bays in two rows of three, made for mini hot sauce bottles in front and oil bottles behind. A nice project for someone whose hot sauce collection has outgrown the fridge door.

Tall light birch plywood organizer with four bays holding oil, balsamic, ketchup, soy and hot sauce bottles at the back and salt, pepper and three spice jars in front, on a wooden kitchen counterTall Oil and Vinegar OrganizerOuter size (W × D × H) 280 × 220 × 120 mm (11.02 × 8.66 × 4.72 in)Parts 8Est. time, 10 W diode (3 mm) 20 min 09 sEst. time, 40 W CO2 (3 mm) 8 min 24 sSVG · DXF →

At 120 mm, the tallest open box in the condiment set. Tall bottles lean less, and the four bays come in two different widths: oil, vinegar and sauce bottles at the back, shakers and spice jars in front.

Light birch plywood condiment station with eight compartments, oil, balsamic, ketchup and mustard bottles at the back and salt, pepper, herb and chili jars in front, on a terrazzo counterEight-Compartment Condiment StationOuter size (W × D × H) 340 × 200 × 90 mm (13.39 × 7.87 × 3.54 in)Parts 12Est. time, 10 W diode (3 mm) 26 min 22 sEst. time, 40 W CO2 (3 mm) 10 min 59 sSVG · DXF →

Eight compartments in two rows of four: one bottle per back cell and one shaker or jar per front cell. It suits a family that cooks a lot, or a small café counter with a full set of condiments.

Common mistake: putting bare plywood under oil bottles. Oil drips run down the bottle and soak straight into raw wood and its end grain, and those dark stains do not sand out easily. Finish the organizer before the first bottle goes in, pay extra attention to the base and the edges, and let the finish cure fully.

A stepped station for sauces and packets

Light birch plywood three-tier condiment organizer with five sauce and oil bottles in the back, shakers and spice jars in the middle and colored sauce packets in four front slots, on a gray kitchen counterThree-Tier Sauce and Packet OrganizerOuter size (W × D × H) 300 × 220 × 100 mm (11.81 × 8.66 × 3.94 in)Parts 11Est. time, 10 W diode (3 mm) 25 min 22 sEst. time, 40 W CO2 (3 mm) 10 min 34 sSVG · DXF →

Three tiers in one box: a long back bay for bottles, two middle bays for shakers and jars, and four low front slots for sauce and seasoning packets. Seven compartments and 11 parts, and the packets finally stop drifting around the drawer. Good for a takeaway counter or a barbecue corner too.

Condiment boxes with a lid

A lid matters when the organizer leaves the kitchen: a picnic, a camping box, a set given as a gift, or a dining table where you want the sauces out of sight between meals.

Birch plywood box with its hinged lid raised on a wooden kitchen island, showing three sections with sauce jars, an olive oil bottle and a dark soy sauce bottle.Hinged Sauce Bottle Box, 3 SectionsOuter size (W × D × H) 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)Parts 8Est. time, 10 W diode (3 mm) 20 min 53 sEst. time, 40 W CO2 (3 mm) 8 min 42 sSVG · DXF →

The smallest lidded box here, 240 × 180 × 80 mm: three sections for sauce jars and small oil bottles under a lid that pivots on round pins cut into the plywood. Eight parts and no hardware.

Long birch plywood box with a sliding lid covering its right half on a stone counter, four open cells holding small bottles of pepper sauce, oil, soy sauce and a golden sauce.Sliding Lid Sauce Box, 8 SectionsOuter size (W × D × H) 340 × 160 × 100 mm (13.39 × 6.30 × 3.94 in)Parts 12Est. time, 10 W diode (3 mm) 33 min 51 sEst. time, 40 W CO2 (3 mm) 14 min 06 sSVG · DXF →

Eight sections in two rows of four, sized for miniature sauce and oil bottles, and a lid that slides in on two rails. A tasting set of small oils or hot sauces in this box makes a very good present.

Large birch plywood chest with its hinged lid open on a stone counter, eight sections holding oil and sauce bottles at the back and spice jars, small oil bottles and napkins in front.Hinged Condiment Chest, 8 SectionsOuter size (W × D × H) 360 × 180 × 90 mm (14.17 × 7.09 × 3.54 in)Parts 10Est. time, 10 W diode (3 mm) 34 min 00 sEst. time, 40 W CO2 (3 mm) 14 min 10 sSVG · DXF →

The widest box and the longest cut in this roundup: 360 × 180 × 90 mm, 10 parts and 34 min 0 s on a 10 W diode. Eight sections under a pin-hinged lid hold oils, salts, peppers and even napkins for the table.

Oil, plywood and finish: problems and fixes

Condiment organizers live in the messiest part of the kitchen. These are the problems you are most likely to meet.

ProblemLikely causeFix
Dark rings and stains on the baseOil soaked into bare woodFinish before use; wipe drips the same day
Tabs loose, box wobblesPlywood thinner than the file versionMeasure the sheet and cut the matching 3, 4, 5 or 6 mm file
Tabs too tight, parts crackPlywood thicker than stated, or kerf not allowed forTest one joint on scrap first; adjust for kerf
Bottles lean or tipBays much wider than the bottleChoose a box with narrower bays or a taller back
Lid sticks after a few weeksPlywood swelled in kitchen steamSeal the lid and rails, sand lightly where it binds
Layout bigger than the bedLayouts here are about 740 to 1364 mm longRearrange the parts into several runs

For the finish, two thin coats of clear varnish or hard wax oil are a sensible default for a box that only touches the outside of bottles. If you are curious about which finishes count as food safe, read what makes laser cut wood food safe. For the joints, how to measure kerf explains the test cut, and the spice rack roundup has matching boxes for jars.

Next step: line up your bottles, count them, and measure the widest base. Pick the file with one bay to spare, cut a test joint, and next week the oil ring on the counter will be a memory.

Read next: Food Safe Finish for Plywood and Laser Cut Ideas for Restaurants and Cafes.

Questions and answers

What is the best layout for an oil and sauce organizer?

Two rows work for most kitchens: tall bottles in the back bays, shakers and small jars in front. For a shallow counter, a single-row tray only 120 mm deep is a better fit.

Will plywood stain from oil bottles?

Bare plywood absorbs oil and stains easily. Seal the organizer with clear varnish or hard wax oil before use and wipe drips the same day.

What plywood thickness should I use for a condiment organizer?

Glass bottles are heavy, so 4–5 mm plywood is a good choice for full organizers. 3 mm works for small trays; always cut the file that matches your measured sheet.

How long does it take to laser cut a condiment organizer?

The 12 files here take about 13 to 34 minutes in 3 mm plywood on a 10 W diode and roughly 5 to 15 minutes on a 40 W CO2, plus assembly and finishing.

Can I make a lidded box for mini sauce bottles?

Yes. The library has an 8-section sauce box with a sliding lid and two boxes with lids that pivot on plywood pins, all without metal hinges.