VisualizationOil and Vinegar Organizer SVG, Tall Bottle Holder Laser Cut File, Condiment and Spice Jar Box DXF, Kitchen Bottle Caddy
The tallest box in the condiment set: a 120 mm high organizer with four bays of two different widths for oil, vinegar and sauce bottles at the back and shakers and spice jars in front. The download has SVG and DXF for 3, 4, 5 and 6 mm plywood; it is 280 × 220 × 120 mm (11.02 × 8.66 × 4.72 in), cut from 8 pieces, with a front that slopes down to 66 mm, and it assembles with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 220 × 120 mm (11.02 × 8.66 × 4.72 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 352 mm
- Cut length
- 6.05 m
- Est. time, 10 W diode (3 mm)
- 20 min 09 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 24 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Open the folder for your plywood thickness and confirm the fit by cutting a single slot and tab on scrap.
- 02Cut the 8 parts and mark the shorter 114.4 mm cross divider for the narrow side and the 165.6 mm one for the wide side.
- 03Build the box on the base, insert the full-depth divider, then push each cross divider into its half.
- 04Sand the tall edges, finish with oil or lacquer, and put long bottles at the back and shakers and jars in front.
Why the extra height
With a 120 mm back wall, this organizer gives tall bottles more support than any other box in this group. Oil and vinegar bottles with long necks stay upright even when you slide the box out from under a cabinet. The front drops to 66 mm, so the jars in the front row are still in plain view.
A narrow side and a wide side
One full-depth divider splits the box into two unequal halves, and each half gets its own cross divider, so there are four bays:
- Narrow left half: olive oil and balsamic at the back, a salt and pepper pair in front.
- Wide right half: three sauce bottles at the back (ketchup, soy sauce and hot sauce in the photo) and three spice jars in front.
The two cross dividers have different lengths, 114.4 and 165.6 mm, so check which goes where before you press them in.
Cutting and sheet layout
All eight parts fit on a 1020 × 352 mm layout. On a smaller bed, split it into two jobs: base and back first, then sides, front and dividers. A 10 W diode cuts 3 mm in one or two passes; 5 and 6 mm need more passes or a CO2 machine. Cutting the 3 mm file takes about 20 min 09 s on a 10 W diode, about 8 min 24 s on a 40 W CO2 and about 4 min 02 s on a 100 W CO2.
For finishing, sand the tall side edges well, since hands grab them, and seal with clear lacquer or oil. Sell it together with a pair of glass oil and vinegar cruets, or as a gift for someone who just moved into a place with a tiny kitchen.
Questions about this file
Which bottles fit best?
The 120 mm back wall steadies 500 ml oil and vinegar bottles and tall sauce bottles; the front bays suit shakers and 100 to 200 ml jars.
Can I make both halves the same width?
Yes, move the slot for the full-depth divider to the center and use two equal cross dividers, keeping slot widths matched to your sheet.
Is 3 mm plywood enough at this height?
It works, but 4 or 5 mm feels much more rigid for a 120 mm tall box loaded with glass.
How do I keep it clean near the stove?
Seal it with a heat-tolerant clear lacquer or hard wax oil and keep it a hand width away from the burners.
Can I put my shop name on it?
Yes, add your own engrave layer on the front or side; the file itself contains cut lines only.
Similar files
