VisualizationSauce Packet Organizer SVG, Three Tier Condiment Station Laser Cut File, Seasoning Packet Holder DXF
A stepped three-tier condiment station: one long back bay for bottles, two middle bays for shakers and jars, and four low front slots for sauce and seasoning packets, seven compartments in all. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; it measures 300 × 220 × 100 mm (11.81 × 8.66 × 3.94 in), is cut from 11 pieces with a sloped front that drops to 50 mm, and joins with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 220 × 100 mm (11.81 × 8.66 × 3.94 in)
- Parts
- 11
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,195 × 332 mm
- Cut length
- 7.61 m
- Est. time, 10 W diode (3 mm)
- 25 min 22 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 34 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the folder for your plywood thickness and run a test cut of one slot to check the tab fit on your laser.
- 02Cut all 11 pieces and label the 82 mm and 62 mm cross dividers so they go into the right rows.
- 03Assemble base, back, sides and front, insert the taller cross divider with its single short divider, then the lower cross divider with its three short dividers.
- 04Sand and seal, then load bottles at the back, shakers and jars in the middle and sauce packets in the four front slots.
Three rows, three heights
This is the only box in the set with three rows of different heights. Two cross dividers, 82 and 62 mm tall, sit between the 100 mm back and the 50 mm front, so every row is a step lower than the one behind it.
- Back row: one open bay across the full width. The photo shows five bottles standing in it: olive oil, balsamic, ketchup, soy sauce and a hot sauce.
- Middle row: split into two bays, one with salt and pepper shakers, the other with three jars of mustard seed, herbs and chili flakes.
- Front row: four narrow slots for flat items. Sachets of sauce, seasoning mixes or tea-sized packets stand upright and are sorted by color.
The front slots are what set this organizer apart: those single-serve packets that usually end up loose in a drawer finally have a place.
Cutting it
There are 11 parts, including two long cross dividers of different heights and four short dividers. Mark the taller cross divider with a pencil before assembly. The 3 mm layout measures 1195.2 × 332 mm, so on beds smaller than that, move the base and one side to a second sheet. Estimated cutting time for the 3 mm file: about 25 min 22 s with a 10 W diode, about 10 min 34 s with a 40 W CO2, about 5 min 04 s with a 100 W CO2. Plan extra passes for 5 and 6 mm.
Who buys this
Food trucks, office kitchens and short-term rental hosts like a station that holds both bottles and packets. Sold flat-packed, it ships in a slim box, and a stained or oiled finish makes it look more finished in listing photos.
Questions about this file
What goes in the four front slots?
They are sized for flat single-serve items: ketchup and soy sauce packets, seasoning sachets, gravy mixes or sugar sticks.
Can the back row take tall bottles?
Yes, the back wall is 100 mm, which supports 250 to 500 ml bottles. Very tall wine-style bottles will lean, so keep those elsewhere.
Which plywood thickness is best for this box?
With five bottles in the back, 4 or 5 mm keeps the long base from sagging; 3 mm suits a lighter, mostly packet setup.
Can I resize it to fit inside a drawer?
Scaling works for the outline, but the slots must stay the width of your plywood, so redraw them after resizing or keep the original scale.
How do I photograph it for an Etsy listing?
Fill all three tiers, especially the colored packets in front, and shoot from slightly above so every row is visible.
Similar files
