VisualizationOil Bottle Organizer SVG, Square Four Section Condiment Box Laser Cut File, Corner Counter Caddy DXF
A square 2 × 2 organizer for oil and sauce bottles at the back and spice shakers at the front, four compartments in total. The download contains SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box is 240 × 240 × 100 mm (9.45 × 9.45 × 3.94 in), is cut from 8 pieces, has a sloped front down to 60 mm and fits together with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 240 × 100 mm (9.45 × 9.45 × 3.94 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 352 mm
- Cut length
- 5.64 m
- Est. time, 10 W diode (3 mm)
- 18 min 48 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 50 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Open the file for your plywood thickness and cut a single test slot to confirm the tabs press in snugly.
- 02Cut the eight parts; the square base and the three 240 mm walls are the largest pieces.
- 03Assemble base, back, sides and the 60 mm front, push the cross divider in, then add the short divider in front and the taller one behind it.
- 04Sand, oil or lacquer, and fill the back bays with bottles and the front bays with shaker pairs.
A square footprint for corners
Most condiment boxes are long and narrow. This one is 240 mm on each side, which suits the corner of a counter, a lazy-susan spot or the space beside a cooktop where a long tray would stick out.
Inside, a cross divider and two short dividers make a simple 2 × 2 grid. The two back bays are full 100 mm height: in the photo one holds olive oil and soy sauce, the other ketchup and a hot sauce. The two front bays sit lower behind a 60 mm front and hold pairs of shakers, salt with pepper on the left and herbs with chili flakes on the right. Each bay is close to 115 mm wide, enough for two bottles.
Choosing the plywood
All four thicknesses are in the download, 3, 4, 5 and 6 mm, each in SVG and DXF. For a box this compact, 4 mm is a good middle ground. Use 3 mm for a lighter gift version; 5 or 6 mm gives chunky edges that look good unfinished. A 10 W diode does 3 mm in one or two passes and needs several passes for 5 and 6 mm.
The 3 mm file should take about 18 min 48 s on a 10 W diode, about 7 min 50 s on a 40 W CO2 and about 3 min 46 s on a 100 W CO2. The layout is 980 × 352 mm; the 240 × 240 mm base is the largest part and fits most beds alone.
Finishing and gift ideas
Sand the tabs flush, then wipe on mineral oil or a clear lacquer. Sold with four matching bottles it makes a tidy hostess gift, and the square shape packs well in a gift box.
Questions about this file
How many items does it hold?
Two bottles per back bay and two shakers per front bay, so about eight items, as in the photo.
Can I cut it in acrylic instead?
Yes, as long as you pick the file whose thickness matches the acrylic sheet and check the fit on a test slot first.
What thickness looks best?
4 mm birch gives a clean, light look; 6 mm makes the box feel solid and is better if you skip glue.
Will it survive oil spills?
Seal every face with lacquer or hard wax oil before use. Sealed plywood wipes clean, raw plywood will stain.
Can I add a label or logo?
Nothing is engraved in the file, but the 240 mm front is a good place to add an engraved word or a small logo in your laser software.
Similar files
