VisualizationOil and Sauce Bottle Organizer SVG, Slanted Condiment Tray Laser Cut File, Wooden Kitchen Caddy DXF
This is a free laser cut file for an open oil and sauce tray with three side-by-side sections and a front wall lower than the back, so the side panels slope down toward you. It comes as SVG and DXF, with separate files for 3, 4, 5 and 6 mm plywood, and builds a 240 × 160 × 80 mm (9.45 × 6.30 × 3.15 in) tray from 7 pieces joined with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 160 × 80 mm (9.45 × 6.30 × 3.15 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 820 × 252 mm
- Cut length
- 4.42 m
- Est. time, 10 W diode (3 mm)
- 14 min 44 s
- Est. time, 40 W CO2 (3 mm)
- 6 min 08 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the set, open the version made for your sheet (3, 4, 5 or 6 mm) and test a single divider slot on an offcut.
- 02Cut all 7 pieces and keep the two slanted side panels together as a pair.
- 03Fit the back and both sides to the base, push the two dividers home, then add the low front wall last.
- 04Sand the corners, seal the tray with food-safe oil and stand the tallest bottles at the back of each bay.
What goes in the three sections
The tray is split into three equal bays that run from front to back. In the photo the left bay carries three small jars (grainy mustard, a dark sauce and a hot sauce), the middle one takes two olive oil bottles with gold caps, and the right one keeps a tall bottle of soy sauce or vinegar upright. The front wall is 56 mm high against an 80 mm back, so labels stay readable and you can lift one bottle out without knocking its neighbour. It sits happily beside the hob or inside a deep drawer.
Cutting and putting it together
There are only 7 pieces: front, back, two sloped sides, base and two dividers. For the 3 mm file a 10 W diode needs about 14 min 44 s, a 40 W CO2 about 6 min 08 s and a 100 W CO2 about 2 min 57 s. Thicker 5 or 6 mm sheet is a job for a CO2 tube, or for several slow passes on a diode. The layout measures 820 × 252 mm, so on a compact bed move the parts onto two or three smaller sheets. Join the back and sides to the base, drop in the dividers, then close the box with the low front. Friction alone holds the joints; a thin line of wood glue makes the tray permanent.
Gift and market ideas
Fill it with three small bottles of infused oil for a housewarming basket, or sell it empty at a craft fair next to your cutting boards. A wipe of food-safe oil or a coat of clear lacquer protects the birch from greasy fingers and drips.
Questions about this file
Will tall oil bottles fit, or only small jars?
The back wall is 80 mm, so bottles of any height stand inside, and the 56 mm front keeps the lower part of each label visible. Each bay is about a third of the 240 mm length and holds two slim bottles one behind the other.
Can I enlarge the tray for one-litre bottles?
Yes, but scale only the outline and then reset every slot to the thickness of your sheet. If the slots grow with the drawing, the tabs will rattle.
Does it work in acrylic?
Clear or white 3 mm acrylic cuts cleanly on a CO2 laser and wipes free of oil easily. Diode lasers cannot cut clear acrylic, so stay with plywood or MDF there.
How do I keep oil stains out of the plywood?
Seal every face, including the underside of the base, with hardwax oil or two coats of clear lacquer before use. Sealed birch will not soak up a drip if you wipe it soon.
Can I put a name or a label on the front?
The file holds cut lines only, but you can add an engraving layer on the front panel in LightBurn before cutting. Keep the text clear of the finger joints at both ends.
Similar files



