DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood box with its hinged lid raised on a wooden kitchen island, showing three sections with sauce jars, an olive oil bottle and a dark soy sauce bottle.Visualization
DW-106031 · UPDATED 11/16/2026

Hinged Box SVG, Sauce Bottle Storage Laser Cut File, Wooden Condiment Box with Lid DXF

This free laser cut file makes a wooden box with three sections and a lid that flips open at the back, pivoting on round pins cut into the plywood. It is sized for sauce jars and small oil bottles, comes as SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood, and builds a 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in) box from 8 pieces that join with tabs and slots.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
860 × 276 mm
Cut length
6.26 m
Est. time, 10 W diode (3 mm)
20 min 53 s
Est. time, 40 W CO2 (3 mm)
8 min 42 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Take the file for your plywood thickness and cut one side panel on scrap first to check the fit of the lid pivot.
  2. 02Cut the 8 parts, marking the lid's front edge in pencil so you install it the right way round.
  3. 03Join base, front, back and the two dividers, then hold the lid between the sides and push both sides on so the pins seat.
  4. 04Open and close the lid a few times, ease any tight pin with sandpaper, and finish the box inside and out.

Lid and pivot pins

The 240 × 176.3 mm lid swings up at the back on small pins that are part of the plywood itself, so there is no metal hardware to buy. The two side panels are a touch taller than the back (84.2 mm against 80 mm) to carry those pivots, and the lid rests open against the wall behind. Close it and the jars stay out of dust and steam near the cooker.

Three bays for bottles and jars

Two dividers split the inside into three sections across the 240 mm width. The photo shows a tomato sauce jar and a mustard jar in the left bay, a square bottle of olive oil in the middle and a dark soy sauce bottle on the right. Bottles taller than about 75 mm have to lie at an angle or go elsewhere, so this box suits small jars, sample bottles and sachets more than full-size oil.

Making it on your laser

Cutting the 3 mm file takes about 20 min 53 s on a 10 W diode, about 8 min 42 s on a 40 W CO2 and about 4 min 11 s on a 100 W CO2. For 5 or 6 mm stock a diode will need extra passes, so a CO2 is the easier route. The layout is 860 × 276 mm; split it over two or three sheets if your bed is smaller. Assemble the base, front, back and dividers first, then fit the sides with the lid pins in their holes, because the lid cannot be added once both sides are fixed. Glue the box joints if you like, but never the pins.

As a gift, add three jars of homemade chutney and a small card tucked under the lid.

Questions about this file

Does the hinged lid need metal hinges or screws?

No, it pivots on pins cut into the plywood, so the whole box is laser-cut wood. Keep glue away from the pins so the lid stays free.

Why is the lid stiff to open?

Usually the plywood is slightly thicker than the file expects, so the pin rubs in its hole. Sand the pin a little or wax it with a candle.

Will a 250 ml oil bottle stand upright inside?

Not with the lid closed, because the inside height is just under 80 mm. Standard bottles have to lie down, which is how the photo shows the oil and soy sauce.

Can I add a design to the lid?

Yes, the lid is a large flat panel, ideal for an engraved herb, a family name or a shop logo that you add in your own software. The file has no engraving of its own.

Which thickness should I use for a hinged box?

3 or 4 mm birch gives the smoothest pivot and a light lid. Thicker sheet works too, but sand the pins until the lid drops closed under its own weight.

Similar files