VisualizationLong Condiment Tray SVG, Four Section Shelf Organizer Laser Cut File, Narrow Oil and Sauce Holder DXF
A long, narrow condiment tray with four bays in a single row for oil bottles, sauces, mustard and spice shakers. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; the tray measures 340 × 120 × 100 mm (13.39 × 4.72 × 3.94 in), is cut from 8 pieces, has sides that slope down to a 60 mm front, and assembles with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 120 × 100 mm (13.39 × 4.72 × 3.94 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,284 × 232 mm
- Cut length
- 5.22 m
- Est. time, 10 W diode (3 mm)
- 17 min 25 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 15 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the 3, 4, 5 or 6 mm file to match your sheet and test-cut one slot before committing the long parts.
- 02Cut the 8 pieces, splitting the long 340 mm parts across two sheets if your bed is short.
- 03Join the back and sides to the base, add the 60 mm front, then slide the three dividers in at even spacing.
- 04Sand the edges, apply clear oil or lacquer, and line up bottles and shakers in the four bays.
Built for shelves and windowsills
At 340 mm long and just 120 mm deep, this tray is made for narrow spots: an open shelf, the strip of counter behind the sink, a windowsill or the top of a cooker hood ledge. Three dividers give four bays in one row, each about 80 mm wide, so nothing hides behind anything else.
The photo shows a practical order from left to right: olive oil and balsamic, then ketchup with a jar of mustard, then a salt and pepper pair, and finally soy sauce next to a small hot sauce. The front is 60 mm high against a 100 mm back, so bottle necks and shaker tops stay visible from the side as well.
Laser settings and sheet size
The 3 mm layout is 1284 × 232 mm, long but narrow. On a typical diode bed, cut the base and the back on one sheet and the front, sides and dividers on another. The 3 mm file takes about 17 min 25 s on a 10 W diode, about 7 min 15 s on a 40 W CO2 and about 3 min 29 s on a 100 W CO2. For 5 and 6 mm a diode needs several passes, so a CO2 laser is quicker.
The long base can bow under heavy glass if it is too thin; 4 mm is a safe choice and 5 mm is even stiffer.
Finishing touches
Knock off the char with 180-grit paper, add a drop of glue under the base tabs if you want it permanent, and seal with lacquer. Cafes and bars use trays like this to keep sauces in one line on the pass or the bar top, and they sell well in sets of two.
Questions about this file
How deep a shelf does it need?
Yes, the depth is only 120 mm (4.72 in), so it suits shelves and ledges that a deeper organizer would overhang.
Can I add a fifth section?
Lengthen the base, front and back and add one more divider; keep the slot widths the same as your plywood thickness.
Will a 340 mm base sag?
With 3 mm and several full glass bottles it can flex slightly; 4 or 5 mm plywood keeps it flat.
Is it safe near the sink?
Seal it fully with lacquer or a hard wax oil and wipe off water; sealed birch handles splashes well.
Can I hang it on a wall instead?
The file has no hanging holes, but you can drill two holes through the 100 mm back wall and screw it to a wall or the side of a cabinet.
Similar files
