DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood box with three bays on a light wood counter, holding small hot sauce bottles, two olive oil pourers and two corked cruets of oil and vinegar.Visualization
DW-106011 · UPDATED 11/16/2026

Oil and Vinegar Holder SVG, Cruet Set Box Laser Cut File, Wooden Olive Oil Bottle Organizer DXF

A free laser cut file for an open, straight-walled box that holds oil and vinegar cruets, pourer bottles and small sauces in three bays. The SVG and DXF come in separate versions for 3, 4, 5 and 6 mm plywood, and the 7 pieces lock together with tabs and slots into a 260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in) box.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
900 × 272 mm
Cut length
5.90 m
Est. time, 10 W diode (3 mm)
19 min 39 s
Est. time, 40 W CO2 (3 mm)
8 min 11 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the 3, 4, 5 or 6 mm version that matches your sheet and test one tab in its slot on an offcut.
  2. 02Cut the 7 parts: four walls, the base and two full-height dividers.
  3. 03Stand the long walls and short walls on the base, then slide both dividers in from above.
  4. 04Lacquer the inside against oil rings and set the cruets and pourer bottles in their bays.

A home for pourers and cruets

All four walls stand 80 mm tall, and two full-depth dividers make three bays across the 260 mm length. The 180 mm depth is the point of this design: glass cruets with handles and bottles fitted with steel pour spouts need more room front to back than a slim sauce bottle. In the photo the left bay holds three little hot sauce bottles, the middle one two olive oils with pourers (one with a sprig of rosemary), and the right one a pair of corked cruets with oil and red wine vinegar. Moving the whole set from counter to table is one lift.

Thickness, time and bed size

The 3 mm and 4 mm files are quick on almost any machine. For the 3 mm file a 10 W diode takes about 19 min 39 s, a 40 W CO2 about 8 min 11 s and a 100 W CO2 about 3 min 56 s. A diode gets through 3 mm in one or two passes; 5 or 6 mm plywood is better on a CO2 or with several passes and a fresh air assist. The parts sit on a 900 × 272 mm layout, so on a smaller bed copy the base onto its own sheet and nest the walls and dividers on a second.

Finishing for a busy counter

Oil bottles always leave a ring sooner or later. Sand the edges smooth, then give the inside two coats of water-based lacquer or a food-safe hardwax oil. Sold as a set with a pair of glass cruets, it makes a good wedding or housewarming present.

Questions about this file

Will cruets with handles fit?

Yes, the bays are 180 mm deep, which leaves room for a handle or a pour spout to stick out behind the bottle. The photo shows two handled cruets side by side in the right bay.

Is the front lower than the back?

No, every wall is 80 mm, so this is a straight-sided box. Bottles taller than that simply stand above the rim.

Is MDF a good substitute for birch here?

MDF of the same thickness works with the matching file, but it swells if oil or water gets into an unsealed edge. Seal MDF well or choose birch plywood for a kitchen.

What happens if I scale it up?

Scaling changes the slot widths too, so the tabs will no longer match your sheet. Resize the panels and keep each slot exactly as wide as the material.

Do the dividers need glue?

They hold by friction in their slots, so you can lift them out to clean. Glue them only if you want one rigid piece.

Similar files