VisualizationSauce Box with Sliding Lid SVG, Hot Sauce Sampler Box Laser Cut File, Mini Bottle Gift Box DXF
A free laser cut file for a long sauce box with a sliding lid and eight sections in two rows of four, sized for miniature sauce and oil bottles. The download has SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood, and the 12 pieces (walls, base, four dividers, two rails and the lid) fit with tabs and slots into a 340 × 160 × 100 mm (13.39 × 6.30 × 3.94 in) box.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 160 × 100 mm (13.39 × 6.30 × 3.94 in)
- Parts
- 12
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,364 × 426 mm
- Cut length
- 10.15 m
- Est. time, 10 W diode (3 mm)
- 33 min 51 s
- Est. time, 40 W CO2 (3 mm)
- 14 min 06 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Use the folder for your plywood thickness and cut a rail plus a strip of the lid edge on scrap to judge the slide.
- 02Cut the 12 pieces on three sheets: lid, base, then walls, dividers and rails.
- 03Stand back and side walls on the base, lock the three short dividers onto the long one, add the rails and the lid, then the front wall.
- 04Wax the rails, give the box a clear finish and drop one mini bottle into each of the eight cells.
A sampler box for small bottles
Three short dividers and one long one turn the inside into eight equal cells, four along the back and four along the front. Each cell takes a single mini bottle, which is exactly what a sampler needs: in the photo you see a red pepper sauce, a bottle of oil, a dark soy and a golden sauce in the four left-hand cells, with the lid slid over the right half. At 100 mm tall it is the deepest of the lidded boxes here, so 100 ml bottles with screw caps stand upright under the lid.
Lid, rails and fit
The 333.4 × 159.7 mm lid slides on two rails and has no hinge or lock. Plywood thickness varies from sheet to sheet, so dry-fit the rails and lid before the 93.7 mm front wall goes on, and sand the lid edges if it drags. A little paraffin wax on the rails makes the slide quiet and smooth.
Cutting it
On the 3 mm file, a 10 W diode runs for about 33 min 51 s, a 40 W CO2 for about 14 min 06 s and a 100 W CO2 for about 6 min 46 s. A diode is comfortable at 3 mm in one or two passes; with 5 or 6 mm stock a CO2 does a much cleaner job. The layout is 1364 × 426 mm, the widest in this set, so on a desktop machine cut the lid and base separately and split the remaining parts over one or two more sheets.
Sauce brands can sell it as an eight-flavour sampler with their logo engraved on the lid. For a Christmas gift, fill the cells with homemade chilli oils and tie a ribbon around the box.
Questions about this file
Which bottles fit one per cell?
Each cell is roughly 80 mm wide and 75 mm deep inside, so 50 to 100 ml sauce or oil bottles fit nicely. The inside height under the lid is a little under 100 mm.
Can I use it without the lid?
Yes, leave the lid and rails off and it works as an open eight-cell tray. The rail slots stay visible, but nothing else changes.
Does the lid lock?
No, the lid only slides on its rails and has no catch. For shipping, a paper band or ribbon around the box keeps it closed.
Is acrylic an option for the lid?
A 3 mm clear acrylic lid cut on a CO2 laser shows the bottles inside. Cut it from the 3 mm file and check that it slides before finishing the wooden parts.
Can I add flavour names over each cell?
Add an engraving layer with eight names on the lid or the front wall in your laser software. The download contains cut lines only.
Similar files



