DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Boxes and organizers · 7 min

Laser Cut Napkin Holder Files: 12 Free Napkin Caddies and Table Organizers

DXF World team, Makers and editors
Short answer

A laser cut napkin holder is a plywood caddy with a bay for napkins and pockets for straws, toothpicks and coasters, joined with tabs and slots. The 12 free files below range from a 6-part, 300 × 160 × 80 mm two-section box to a 12-part three-step stand 180 mm tall, including caddies for cafés and boxes with sliding or pin-hinged lids. Each comes in SVG and DXF for 3, 4, 5 and 6 mm plywood and cuts in about 13 to 29 minutes on a 10 W diode (3 mm).

Eight people at the table, the soup is on, and the napkins are still in their plastic bag on the counter next to a fistful of straws. A laser cut napkin holder turns that mess into a small, warm piece of wood in the middle of the table: napkins standing up, coasters stacked beside them, toothpicks in their own pocket.

This roundup lists 12 napkin and table caddy files from the DXF World library. All of them are box caddies rather than flat two-panel napkin stands: the napkins stand upright or lie flat in a bay, with pockets for straws, toothpicks and coasters beside them. There are simple two- and three-section boxes, caddies with pockets, stepped caddies for cafés and two boxes with lids. Every download has SVG and DXF drawn separately for 3, 4, 5 and 6 mm plywood, and all 17 table organizers are in the napkin and table organizers category.

Laser cut napkin holder files compared

FileTypeOuter size, mm (W × D × H)Parts10 W diode, 3 mm
Napkin and coaster box, 2 sectionsOpen, one divider300 × 160 × 80613 min 43 s
Napkin caddy, 3 sectionsOpen, wide center bay280 × 200 × 90717 min 2 s
Sloped napkin and straw caddyOpen, sloped front240 × 160 × 80714 min 35 s
Four-pocket table caddyOpen grid, 2 × 2280 × 220 × 80818 min 40 s
Napkin caddy, front pocketsBack row + front pockets300 × 200 × 90819 min 24 s
Five-slot napkin and straw organizerOpen, tall back320 × 220 × 100925 min 1 s
Long narrow table caddyOpen, 160 mm deep360 × 160 × 90819 min 53 s
Napkin caddy, tiered side columnOpen, stepped column300 × 200 × 90818 min 11 s
Three-row serving caddyStepped rows340 × 240 × 100823 min 40 s
Three-step napkin and coaster standTiered stand260 × 200 × 1801228 min 30 s
Sliding lid napkin boxSliding lid on rails280 × 160 × 801023 min 50 s
Hinged lid napkin boxLid on plywood pins240 × 180 × 80820 min 53 s

The cut times are estimates for the 3 mm file. On a 40 W CO2 the same caddies take roughly 5 to 12 minutes. Speed, power and passes depend on your machine and your plywood, so test on scrap first.

Napkin sizes and the bay they need

Before you pick a caddy, look at the napkins you buy. Paper napkins come in a few common sizes and are sold folded, so the folded size is what has to fit.

Napkin typeTypical unfolded sizeTypical folded sizeFits best in
Cocktail or beverageabout 24–25 cm squareabout 12–13 cm squareSmall pockets, the 3-section caddies
Lunchabout 33 cm squareabout 16–17 cm squareA wide bay or the back row of a caddy
Dinnerabout 40 cm squareoften folded to about 10 × 20 cm or 20 cm squareThe largest bays; check the depth

Sizes vary between brands and countries, so measure a folded napkin from your own pack and compare it with the width of the bay and the outer size of the caddy.

Simple napkin caddies for the home table

Few parts, few sections, quick to cut. These are the ones to make first.

Small birch plywood box with two sections, one holding square napkins, metal straws and wrapped toothpicks and the other a stack of square cork coasters, on a beige stone counter near a sinkNapkin and Coaster Box, 2 SectionsOuter size (W × D × H) 300 × 160 × 80 mm (11.81 × 6.30 × 3.15 in)Parts 6Est. time, 10 W diode (3 mm) 13 min 43 sEst. time, 40 W CO2 (3 mm) 5 min 43 sSVG · DXF →

The simplest file in the set: 6 parts, one divider and 13 min 43 s on a 10 W diode. One side holds napkins with a few straws, the other a stack of coasters.

Birch plywood napkin caddy with a wide center bay of paper napkins, wrapped toothpicks on the left and metal straws with cork coasters on the right, on a speckled kitchen counterNapkin Caddy, 3 SectionsOuter size (W × D × H) 280 × 200 × 90 mm (11.02 × 7.87 × 3.54 in)Parts 7Est. time, 10 W diode (3 mm) 17 min 02 sEst. time, 40 W CO2 (3 mm) 7 min 06 sSVG · DXF →

A wide center bay for paper napkins and two narrower side sections for toothpicks, straws and coasters. It looks balanced from every side of the table, which matters for a piece that sits in the middle.

Light birch plywood napkin caddy with three sections and a sloped front, holding white napkins, cork coasters, toothpicks and metal straws on a kitchen counterSloped Napkin and Straw Caddy, 3 SectionsOuter size (W × D × H) 240 × 160 × 80 mm (9.45 × 6.30 × 3.15 in)Parts 7Est. time, 10 W diode (3 mm) 14 min 35 sEst. time, 40 W CO2 (3 mm) 6 min 05 sSVG · DXF →

Three sections side by side behind a low front that rises to a taller back. At 240 × 160 × 80 mm it is the smallest open caddy here and leaves room on a small kitchen table.

Pro tip: coasters stack better in a pocket that is just a little bigger than they are. If you also cut your own coasters, decide their size first; what size a laser cut coaster should be gives typical numbers.

Caddies with pockets for straws and toothpicks

When straws, toothpicks and coasters all need their own place, more pockets beat a bigger box.

Low birch plywood table caddy with four pockets in a two by two grid holding folded napkins, wrapped toothpicks, metal and silicone straws and printed coasters on a marble counterFour-Pocket Napkin Table CaddyOuter size (W × D × H) 280 × 220 × 80 mm (11.02 × 8.66 × 3.15 in)Parts 8Est. time, 10 W diode (3 mm) 18 min 40 sEst. time, 40 W CO2 (3 mm) 7 min 47 sSVG · DXF →

Four pockets in a two-by-two grid, with the back row taller than the front, so the small things in front never hide behind the napkins. Only 80 mm tall and easy to pass across the table.

Birch plywood napkin caddy with paper napkins standing in the back row and three front pockets of wrapped toothpicks, metal and coloured straws, and cork coasters on a wooden kitchen counterNapkin Caddy With Front PocketsOuter size (W × D × H) 300 × 200 × 90 mm (11.81 × 7.87 × 3.54 in)Parts 8Est. time, 10 W diode (3 mm) 19 min 24 sEst. time, 40 W CO2 (3 mm) 8 min 05 sSVG · DXF →

The napkins stand upright in a full-width back row, and three low pockets in front take toothpicks, straws and coasters. It reads like a tidy little shelf from the guest's side.

Birch plywood table organizer with five slots holding a stack of paper napkins, wrapped toothpicks, cork coasters and metal and glass straws on a wooden kitchen counterFive-Slot Napkin and Straw OrganizerOuter size (W × D × H) 320 × 220 × 100 mm (12.60 × 8.66 × 3.94 in)Parts 9Est. time, 10 W diode (3 mm) 25 min 01 sEst. time, 40 W CO2 (3 mm) 10 min 25 sSVG · DXF →

Four full-depth dividers make five slots under a 100 mm back that slopes down to a low front. Good for reusable metal or bamboo straws, which stand upright better in narrow slots.

Long narrow birch plywood table caddy with a bay of square napkins and sections holding wrapped toothpicks, metal and gold straws, cork coasters and sugar packets on a kitchen counter with green cabinetsLong Narrow Napkin Table CaddyOuter size (W × D × H) 360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in)Parts 8Est. time, 10 W diode (3 mm) 19 min 53 sEst. time, 40 W CO2 (3 mm) 8 min 17 sSVG · DXF →

Only 160 mm deep but 360 mm long: a napkin bay along the full depth plus a divided section for straws, toothpicks, coasters and sugar packets. It fits along a wall, a bar counter or a narrow café table. Its layout is about 1424 mm long, so split it on a small bed.

Common mistake: cutting a café caddy from 3 mm plywood and leaving it bare. Tables in a café get wiped with a wet cloth many times a day, and raw plywood edges soak up water, swell and go grey within weeks. For busy tables, cut 4 or 5 mm, seal every edge, and let the finish cure fully before the caddy goes out.

Stepped caddies and stands for cafés and buffets

Steps put the small things at the front and the napkins at the back, so a guest can grab everything without lifting anything else.

Birch plywood napkin caddy with a large bay of square lunch napkins and three stepped side tiers holding metal straws, wrapped toothpicks and cork coasters on a beige stone counterNapkin Caddy With Tiered Side ColumnOuter size (W × D × H) 300 × 200 × 90 mm (11.81 × 7.87 × 3.54 in)Parts 8Est. time, 10 W diode (3 mm) 18 min 11 sEst. time, 40 W CO2 (3 mm) 7 min 35 sSVG · DXF →

One large bay where lunch napkins lie flat and a narrow column of three stepped tiers for straws, toothpicks and coasters. Flat napkins are easier to take one at a time, so this is a good choice for a self-service counter.

Large birch plywood serving caddy with stepped rows of standing napkins, wrapped toothpicks, metal and gold straws, cork and printed coasters on a white marble kitchen counterThree-Row Serving Table CaddyOuter size (W × D × H) 340 × 240 × 100 mm (13.39 × 9.45 × 3.94 in)Parts 8Est. time, 10 W diode (3 mm) 23 min 40 sEst. time, 40 W CO2 (3 mm) 9 min 52 sSVG · DXF →

The largest caddy of the set at 340 × 240 × 100 mm: three stepped rows across the full width, the front row split in two. Yet it is only 8 parts and 23 min 40 s on a 10 W diode.

Birch plywood three-step stand with six slots holding white napkins, steel straws, cork coasters, toothpicks and bamboo picks on a kitchen counterThree-Step Napkin and Coaster StandOuter size (W × D × H) 260 × 200 × 180 mm (10.24 × 7.87 × 7.09 in)Parts 12Est. time, 10 W diode (3 mm) 28 min 30 sEst. time, 40 W CO2 (3 mm) 11 min 52 sSVG · DXF →

A proper display stand, 180 mm tall, with two slots on each of its three steps: six places for napkins, coasters, straws and cocktail picks. The 12 parts carry small engraved numbers, so assembly is no puzzle.

Napkin boxes with a lid

A lid keeps napkins clean and dry on a terrace, in a camper or in a cupboard between parties.

Birch plywood box with a half-open sliding lid and three compartments holding paper towels, cork coasters, toothpicks and metal straws on a kitchen counterSliding Lid Napkin and Straw BoxOuter size (W × D × H) 280 × 160 × 80 mm (11.02 × 6.30 × 3.15 in)Parts 10Est. time, 10 W diode (3 mm) 23 min 50 sEst. time, 40 W CO2 (3 mm) 9 min 56 sSVG · DXF →

A flat lid slides in along two rails over three compartments for napkins, coasters and straws. The ten parts include the two rails and the lid itself.

Birch plywood box with its hinged lid tipped open, showing three compartments with printed napkins, cork coasters, metal straws and toothpicks on a kitchen tableHinged Lid Napkin and Coaster BoxOuter size (W × D × H) 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)Parts 8Est. time, 10 W diode (3 mm) 20 min 53 sEst. time, 40 W CO2 (3 mm) 8 min 42 sSVG · DXF →

The lid flips open at the back on pins cut into the plywood, so there is no hardware at all. Three compartments, 240 × 180 × 80 mm, a neat box for the good cloth-napkin-and-coaster set.

How to cut a napkin caddy

  1. Measure your plywood with calipers and download the matching version.
  2. Cut one tab and slot from scrap and check the fit. If it is off, how to measure kerf shows the fix.
  3. Split long layouts into runs that fit your bed. The files here are about 820 to 1424 mm long as laid out.
  4. Assemble the dividers into the base, then the walls; glue the corners for café use.
  5. Sand, seal every edge, and let it cure before use.

For a café order of ten or twenty caddies, the cut times in the table make pricing much easier: see how to price laser cut products, and engrave the café's name on the front for a finished look.

Next step: fold one napkin from your pack, measure it, and choose the caddy whose bays fit it. Cut a single one for your own table first; once it has survived a week of dinners, it is ready to be made for others.

Read next: Laser Cut Ideas for Restaurants and Cafes and Laser File Bigger Than Your Bed? Split It Across Sheets.

Questions and answers

What size napkins fit a laser cut napkin holder?

Folded cocktail napkins are typically about 12–13 cm square and lunch napkins about 16–17 cm. Measure a folded napkin from your pack and compare it with the bay width and the outer size of the caddy.

What plywood thickness is best for a napkin caddy?

3 mm is fine for a home table caddy. For café tables that are wiped all day, 4 or 5 mm with sealed edges lasts much longer.

How long does it take to laser cut a napkin holder?

The 12 files here take about 13 to 29 minutes in 3 mm plywood on a 10 W diode and roughly 5 to 12 minutes on a 40 W CO2, plus assembly and finishing.

Can I make napkin caddies for a café or restaurant?

Yes, the stepped caddies and the three-step stand are made for self-service counters and tables. Seal every edge and add the café's name with engraving.

How do I keep a wooden napkin holder clean?

Seal it with two thin coats of clear varnish or hard wax oil, including the edges, and wipe it with a damp cloth rather than soaking it.