VisualizationNapkin and Coaster Holder SVG, Two Section Table Box Laser Cut File, Small Napkin Organizer DXF
A small two-section box for the table: one side for napkins with straws and toothpicks, the other for a stack of coasters. It is offered as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 300 × 160 × 80 mm (11.81 × 6.30 × 3.15 in), is cut from just 6 pieces with one divider, has a front lower than the back, and assembles with tabs and slots. Free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 160 × 80 mm (11.81 × 6.30 × 3.15 in)
- Parts
- 6
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 940 × 252 mm
- Cut length
- 4.12 m
- Est. time, 10 W diode (3 mm)
- 13 min 43 s
- Est. time, 40 W CO2 (3 mm)
- 5 min 43 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the 3, 4, 5 or 6 mm file and cut one slot on scrap to check the fit.
- 02Cut the six parts: base, back, low front, two sloped sides and the single divider.
- 03Push the divider into the base, add the sloped sides, then the back, and close it with the low front.
- 04Sand and lacquer the box, then fill one side with napkins, straws and toothpicks and the other with coasters.
Simple two-part layout
One divider splits this box into two halves. The photo shows square napkins in the left half with a few metal straws and wrapped toothpicks tucked behind them, and a stack of square cork coasters in the right half. At only 160 mm deep and 80 mm tall at the back it is the slimmest caddy in the napkin set and fits on a narrow breakfast bar or a windowsill table. The front drops to 48 mm.
Quick to cut
Six pieces and a short cut line make this the fastest napkin caddy here. The 3 mm layout is 940 × 252 mm. For the 3 mm file allow about 13 min 43 s on a 10 W diode, about 5 min 43 s on a 40 W CO2 or about 2 min 45 s on a 100 W CO2. A diode handles 3 mm in one or two passes; 5 and 6 mm call for several passes or a CO2 machine. On a short bed, cut the base and the long panels on separate sheets.
Sets and finishing
Because it is quick, this box is a good add-on: cut it in the same plywood as one of the cutlery caddies and sell the pair as a table set. Ten of them for a wedding or a cafe terrace is an afternoon of cutting.
Sand the sloped edges and corners, then seal with clear lacquer. If coasters come back wet, a sealed base keeps rings from forming. Glue is optional; the tabs hold the six pieces together well.
Questions about this file
What size coasters fit?
Square or round coasters up to about 140 mm across fit in the right half, depending on your plywood thickness.
Can I use it without the divider?
Yes, leave the divider out for one open tray; the empty slots in the base can be filled or left as a detail.
Which thickness should I choose for a small box like this?
3 mm keeps it light and quick; 4 mm feels a bit more solid on a table. Thicker sheets mostly add weight here.
Does it need glue?
No. Six pieces with tight tabs stay together; glue makes sense only for boxes you plan to ship.
Can I engrave initials on it for a wedding?
Yes, add the initials as an engraving layer on the front before cutting; the file itself has cut lines only.
Similar files
