VisualizationHinged Box SVG, Napkin Box With Lid Laser Cut File, Wooden Coaster and Straw Storage DXF
A free napkin box whose lid flips open at the back on pins cut into the plywood, with three compartments inside for napkins, coasters and straws. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in) and is made of 8 pieces joined with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 860 × 276 mm
- Cut length
- 6.26 m
- Est. time, 10 W diode (3 mm)
- 20 min 53 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 42 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood thickness, then cut a test slot and one side wall to confirm the lid pins turn freely in their holes.
- 02Cut all 8 parts, placing the base and lid on a second sheet if your laser bed is under 860 mm.
- 03Join the base, back, front and two dividers, fit the lid pins into the first side wall, then add the second side wall to trap them.
- 04Wax the pins, sand all edges, and finish with oil before filling the box with napkins, coasters and straws.
How the lid works
The lid is a single 240 × 176 mm panel. Two round pins at its back corners sit in holes near the top of the side walls, so it tips up and rests open against the back, just as the photo shows. No metal hinges, screws or magnets are needed; the pivot is cut from the same plywood. The side walls are a little taller at the back to carry the pins, and the front wall is slightly lower so the closed lid lies flat.
Inside the box
Two dividers make three compartments. The largest, on the left, fits a stack of printed paper napkins lying flat. The middle one stores a column of cork coasters, and the narrow section on the right takes metal straws and a small glass of toothpicks. Closed, the box keeps party napkins clean in a sideboard; open, it works as a serving caddy on the table.
Cutting and fitting the pins
Cutting time for the 3 mm file is about 20 min 53 s on a 10 W diode, about 8 min 42 s on a 40 W CO2 and about 4 min 11 s on a 100 W CO2. The layout is 860 × 276 mm, so a smaller bed needs the base and lid moved to a separate sheet. For a diode laser, 3 or 4 mm birch is the comfortable choice; thicker plywood needs extra passes and a well-focused beam to keep the pin holes round.
Assemble the base, back, dividers and front first, then slip the lid pins into one side wall, swing the other side wall into place and press it down. Leave the pins unglued so the lid moves. A little paste wax on the pins makes the lid swing smoothly.
Questions about this file
Do I need to buy hinges for this box?
No, the lid turns on two pins that are part of the lid itself. They sit in holes cut in the side walls.
The lid squeaks or binds. How do I fix it?
Rub a little wax or a soft pencil on the pins. If it still binds, sand the pins lightly, since slightly thicker plywood can make them tight.
Can I engrave a design on the lid?
The flat lid takes engraving well. Add a monogram, a wedding date or a botanical sprig as an engrave layer before you cut.
How big can the napkins be?
The left compartment fits standard folded beverage and luncheon napkins lying flat. Large dinner napkins need an extra fold.
Can I make the box in acrylic?
The tabs work in acrylic of a matching thickness, but brittle acrylic pins may snap. Plywood is the better material for the lid pivot.
Similar files



