VisualizationLong Table Caddy SVG, Narrow Napkin Holder Laser Cut File, Bar Counter Condiment Organizer DXF
A long, narrow table caddy only 160 mm deep, with a full-depth napkin bay and a divided section for straws, toothpicks, coasters and sugar packets, four compartments in all. It comes as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in), has 8 pieces, a front lower than the back, and assembles with tabs and slots. Free file.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,424 × 262 mm
- Cut length
- 5.97 m
- Est. time, 10 W diode (3 mm)
- 19 min 53 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 17 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the folder for your plywood thickness and cut one test slot; the long layout may need two or three sheets on a small bed.
- 02Cut the base, two long walls, two sloped ends, the napkin bay divider, the long cross divider and the short front divider.
- 03Slot the short divider onto the cross divider, place them and the napkin bay divider in the base, then add the ends, back and front.
- 04Sand, seal, and fill the bay with napkins and the divided section with straws, toothpicks, coasters and sugar.
Made for narrow spaces
At 360 mm long but just 160 mm deep, this caddy fits along a bar counter, a window ledge or the middle of a long dining table without crowding the plates. The back is 90 mm tall and the sides slope down to a 54 mm front.
A full-depth divider closes off the napkin bay at one end, where the photo shows a stack of square napkins. The rest of the length is split by a long cross divider into a back row and a front row, and a short divider splits the front row into two pockets. In the photo that area holds wrapped toothpicks, metal and gold straws, round cork coasters and sugar packets.
Cutting and assembly
The 3 mm layout is long and thin: 1424 × 262 mm. On a typical 400 or 600 mm bed, cut the base and the two long walls on separate sheets, then group the small parts together. For the 3 mm file: about 19 min 53 s on a 10 W diode, about 8 min 17 s on a 40 W CO2, about 3 min 59 s on a 100 W CO2. Diodes manage 3 mm in one or two passes and need several for 5 to 6 mm.
Fit the short front divider onto the long cross divider, then set that pair and the napkin bay divider into the base. Add the sloped sides, the back and the low front last. Glue is optional.
Sealing it and who buys it
Sand the long top edges carefully and seal with lacquer. Bars and coffee shops that keep straws and napkins along the pickup counter are natural buyers, and a long caddy with a laser-engraved name on the back is a simple custom product.
Questions about this file
Is 160 mm deep enough for napkins?
Yes for cocktail and small lunch napkins folded square; large dinner napkins should be folded once more.
Will it fit on a bar counter?
At 360 by 160 mm it sits along a narrow counter or shelf without blocking the serving area.
Can I make it longer?
You can stretch the length in your design software, but keep the slot widths at your plywood thickness and lengthen the base, walls and cross divider together.
Can I cut it in acrylic for a bar?
Acrylic in a matching thickness works and wipes clean; cut the 3 or 4 mm file and press tabs in gently.
How do I keep sugar packets dry?
Seal the inside well and wipe up spills; the caddy is open, so it will not protect contents from moisture in the air.
Similar files
