VisualizationNapkin and Straw Organizer SVG, Five Slot Table Caddy Laser Cut File, Coffee Bar Condiment Box DXF
A five-slot table organizer for napkins, reusable straws, toothpicks and coasters, with four full-depth dividers and a tall back that slopes down to a low front. It is delivered as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 320 × 220 × 100 mm (12.60 × 8.66 × 3.94 in), is cut from 9 pieces and assembles with tabs and slots. Downloading it costs nothing.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 220 × 100 mm (12.60 × 8.66 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,224 × 332 mm
- Cut length
- 7.50 m
- Est. time, 10 W diode (3 mm)
- 25 min 01 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 25 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood; 3 or 4 mm keeps the five slots widest. Cut a test slot first.
- 02Cut the base, tall back, low front, two sloped sides and four dividers, splitting the layout over extra sheets if needed.
- 03Stand all four dividers in the base, then attach the sloped sides, the back and the low front.
- 04Sand and seal, then fill the five slots with napkins, straws, toothpicks and coasters.
Five slots side by side
Four dividers run from front to back and divide the 320 mm length into five sections, each the full 220 mm deep. The photo shows a napkin stack, wrapped toothpicks, round cork coasters and two narrow slots of metal and glass straws, so one caddy covers everything a coffee bar or a family table needs. At 100 mm the back is one of the tallest in the napkin set, which keeps long straws upright; the front is 60 mm.
Thickness and cutting
With five dividers in a row, plywood thickness eats into the slot widths. The 3 mm file leaves the most room inside; 4 mm is a good balance; 6 mm gives a heavy, sturdy piece for a busy cafe counter.
The 3 mm layout is 1224 × 332 mm, so mid-size machines will need it split across two or three sheets: base alone, then walls, then the four dividers. For the 3 mm file allow about 25 min 01 s on a 10 W diode, about 10 min 25 s on a 40 W CO2 and about 5 min 00 s on a 100 W CO2. On thicker plywood a diode needs several passes.
Assembly, finish and selling ideas
Set all four dividers in the base, then add the sloped sides, the back and the front. Dry-fit first; glue only if it will be moved a lot. Sand the dividers' sloped tops, then seal the whole caddy with lacquer or oil so coffee splashes wipe off.
Coffee bar organizers are a popular search on Etsy. Photograph it next to a coffee machine with straws and sugar sticks, and offer a personalised version with a family name engraved on the back.
Questions about this file
Will long reusable straws stay upright?
Yes; the 100 mm back wall and full-height dividers support straws of normal length standing in a narrow slot.
How wide is each slot?
About 60 mm in the 3 mm version; thicker plywood makes each slot a few millimetres narrower.
Can I turn it into a tea or coffee station?
Yes; the same slots hold tea bags, sugar sticks and stirrers just as well as napkins and straws.
Can I scale it to fit my counter?
You can change the length and depth, but keep the slots at your exact plywood thickness after resizing, or the dividers will wobble.
What finish should I use near a coffee machine?
Water-based polyurethane or a hard wax oil resists coffee and water spills and is easy to wipe clean.
Similar files
