DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood three-step stand with six slots holding white napkins, steel straws, cork coasters, toothpicks and bamboo picks on a kitchen counterVisualization
DW-105061 · UPDATED 11/16/2026

Tiered Napkin Stand SVG, Three Step Coaster Rack Laser File, Cafe Condiment Station DXF

A free three-step display stand for napkins, coasters, straws and cocktail picks, with two slots on each step for six compartments in total. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the stand measures 260 × 200 × 180 mm (10.24 × 7.87 × 7.09 in), has 12 tab-and-slot pieces and small engraved part numbers to help assembly.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
260 × 200 × 180 mm (10.24 × 7.87 × 7.09 in)
Parts
12
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,060 × 313 mm
Cut length
8.55 m
Est. time, 10 W diode (3 mm)
28 min 30 s
Est. time, 40 W CO2 (3 mm)
11 min 52 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the file for your sheet thickness and cut a single test slot to check that a tab slides in snugly.
  2. 02Cut the 12 parts, spreading the 1060 mm layout over two or three sheets if your bed is smaller.
  3. 03Using the engraved numbers, slot the shelves, step boards, front board and brace into one side, close it with the second side and drop in the three dividers.
  4. 04Lacquer the stand, then fill the top step with napkins and straws and the lower steps with coasters and picks.

Six slots on three levels

The steps rise toward the back, so the tallest items sit at the rear and nothing in front hides them. In the photo the top step holds a stack of white napkins beside a bundle of steel straws. The middle step shows round and square cork coasters side by side, and the bottom one keeps a glass of toothpicks next to a glass of knotted bamboo picks. One short divider on each shelf splits it into a left and a right slot. It suits a cafe self-service counter, a home coffee corner or a buffet table at a party.

Putting the steps together

The file has 12 pieces: two stepped sides, a front board, two step boards, three shelves, a brace and three dividers. Each piece carries a small engraved number, which makes it easy to match shelves to their slots. Stand one side on the bench, fit the shelves, step boards, front board and brace into it, then cap the other side and push the three dividers down onto the shelves.

On a 10 W diode the napkin stand takes about 28 min 30 s for the 3 mm file; a 40 W CO2 needs about 11 min 52 s and a 100 W CO2 about 5 min 42 s. The layout runs 1060 × 313 mm, longer than most hobby beds, so plan to spread the parts over two or three sheets. On a diode laser, 5 and 6 mm sheets need several slow passes.

Branding and finishing

A coffee shop can engrave its logo on the front board before cutting, and two stands side by side cover a whole service station. Give the plywood a coat of clear lacquer so spilled drinks wipe straight off.

Questions about this file

How many items can each step hold?

Every step is split into two slots, so you get six places in total. A stack of napkins or a pile of 10 cm coasters fits in each slot.

Why is each napkin stand piece marked with a digit?

They are part numbers engraved by the file so you can tell the shelves and step boards apart. They are small, and a light sanding takes them off after assembly if you want clean faces.

Will it stand steady with full glasses of picks?

Yes, the brace and the wide 200 mm footprint keep it from rocking. Glue the joints if it will live on a busy cafe counter.

Can I cut the stand from MDF or acrylic?

MDF of the same thickness works and paints well. For acrylic, measure the sheet and pick the file that matches it closest, since cast acrylic is often slightly off its nominal size.

Which plywood thickness is best for a counter display?

Four or 5 mm feels solid for daily use in a shop. Choose 3 mm for a light home version that cuts quickly on a diode laser.

Similar files