VisualizationTwo Section Sliding Lid Tea Box SVG, Tea Bag and Tin Storage Laser Cut File, Wooden Lidded Tea Box DXF
A free two-section tea box with a sliding lid, offered as a laser cut file in SVG and DXF with separate versions for 3, 4, 5 and 6 mm plywood. The box is 280 × 200 × 100 mm (11.02 × 7.87 × 3.94 in) and has two compartments: a wide one for tea bags and a narrow one for tins. It is cut as 9 pieces that join with tabs and slots, and the lid slides in on two rails, with no hinge and no lock.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 200 × 100 mm (11.02 × 7.87 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 516 mm
- Cut length
- 7.64 m
- Est. time, 10 W diode (3 mm)
- 25 min 28 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 37 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the version for your plywood and test one tab joint on scrap, because the lid and rails depend on an accurate fit.
- 02Cut the 9 parts: front, back, two sides, base, the divider, two rails and the lid.
- 03Join the walls to the base, set the divider in its slots, then fix the rails along both side walls level with each other.
- 04Slide the lid in, ease any tight spot with sandpaper or wax, finish the box and fill both bays.
A wide bay and a narrow one
One divider runs from front to back and splits the box into two unequal parts. The larger left side takes tea bags standing on edge in rows: in the photo there are red, yellow and green packs. The narrow right side holds three small round tins of loose tea lined up one behind another. In the photo that side is also split by two short cross pieces; they are not in the file, but you can cut two strips from offcuts if you want each tin in its own pocket. The divider stops below the rim so the closed lid clears it.
Fitting the sliding lid
The lid runs on two thin rails fixed to the inside of the side walls, and the front wall is a little lower than the back so the lid can pass over it. Cut, assemble and try the lid before any finish goes on; if it drags, sand the long edges of the lid a touch or rub on candle wax. Keep varnish thin on these edges.
For the 3 mm file allow about 25 min 28 s on a 10 W diode, about 10 min 37 s on a 40 W CO2 or about 5 min 06 s on a 100 W CO2. The layout is 980 × 516 mm, so smaller machines should split it over two sheets, with the lid and base on one of them. Thick 5 or 6 mm stock needs more laser power than a 10 W diode offers in a single pass.
Gift ideas
This mid-size box suits a pantry shelf or a desk drawer. Fill it with a mix of bagged and loose teas for a birthday or a thank-you gift. The flat lid is a ready surface for an engraved monogram or a leaf pattern you add yourself, and a tea seller can offer it as a two-tea sampler box.
Questions about this file
What fits in the narrow tin section?
Small round tins of loose tea, about three in a row front to back, or a stack of coffee sticks and sugar sachets.
Will the lid stay closed if I carry the box?
It slides freely and has no catch, so hold it shut or carry the box flat.
Can the box hold more than two kinds of tea?
Add short cross pieces from scrap plywood in either section; the file itself cuts one divider.
Which thickness works best for the sliding lid?
3 or 4 mm gives a light lid that glides easily; 6 mm makes a very solid box, but the lid gets heavy.
How should I finish it for a kitchen shelf?
A thin coat of food-safe oil or water-based lacquer is enough; avoid a thick build-up on the lid edges and rails.
Similar files



