DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with a sliding lid pushed half open over five slots, each holding a small bottle of chili oil, olive oil, balsamic, herb oil or red vinegar, on a marble kitchen counterVisualization
DW-106030 · UPDATED 11/19/2026

Sliding Lid Oil Bottle Box SVG, Infused Oil Gift Box Laser Cut File, Wooden Vinegar Bottle Case DXF

This is a low wooden box with a sliding lid that holds five slim oil, vinegar or sauce bottles lying in separate slots running front to back. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood and makes a 400 × 200 × 80 mm (15.75 × 7.87 × 3.15 in) box from 12 pieces that fit together with tabs and slots, including the lid and the two rails it slides on.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
400 × 200 × 80 mm (15.75 × 7.87 × 3.15 in)
Parts
12
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,602 × 496 mm
Cut length
10.39 m
Est. time, 10 W diode (3 mm)
34 min 39 s
Est. time, 40 W CO2 (3 mm)
14 min 26 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file for your plywood thickness and test one tab in a slot on scrap; the lid should also slide freely between two test rails.
  2. 02Cut the base, four walls, four dividers, two rails and the lid, spreading them over several sheets if needed.
  3. 03Join the walls around the base, push the four dividers into their slots, then glue the two rails in place and check the lid slides before the glue sets.
  4. 04Sand the lid edges, seal all surfaces, lay one bottle in each slot and slide the lid closed.

Five slots for gift bottles

Four dividers split the 400 mm length into five equal slots. At 80 mm high the box is meant for bottles that lie down rather than stand, so each slot cradles one slim bottle along the 200 mm depth. The photo shows a chili oil, an olive oil, a dark balsamic, a herb oil with peppercorns and a red wine vinegar, each in its own slot so the glass never knocks together. The dividers are about 71 mm tall, a little below the walls, which leaves room for the lid to pass over them.

How the lid works

Two narrow rails glue inside the top edge of the box and the flat lid slides in on them. There is no hinge, catch or lock: push the lid part way open to lift out one bottle, or slide it off completely to fill the box. Sand the lid edges and rails smooth before assembly so it glides without sticking.

Cutting and finishing

The 3 mm layout measures 1602 × 496 mm, so on a desktop laser you will need to spread the twelve pieces over three or four sheets; the lid and base each want a sheet to themselves. Cutting takes about 34 min 39 s on a 10 W diode, about 14 min 26 s on a 40 W CO2 and about 6 min 56 s on a 100 W CO2, all for the 3 mm file. Thicker 5 and 6 mm plywood needs a stronger laser or extra passes. Finish with clear lacquer or a hard wax oil. As a gift, fill it with five homemade infused oils, engrave your own label on the lid, or offer it on Etsy as a tasting set box for olive oil producers and delis.

Questions about this file

How long can the bottles be?

Each slot runs the full inside depth of the 200 mm box, so slim bottles a little shorter than that lie down comfortably. Tall wine-style oil bottles will not fit.

Is there a catch or hinge on the sliding lid?

No, it simply slides on two rails and can be pulled off completely. A small engraved finger notch helps if you want an easier grip.

Can I cut this gift box from MDF or acrylic?

MDF works if you pick the file that matches its thickness. Clear acrylic makes a nice show lid, but cut a test slot first because acrylic melts slightly wider than wood.

Why should I not just resize the file to fit bigger bottles?

Scaling also changes the slot widths, which must match your sheet thickness. If you enlarge it, redraw the slots back to the material size.

Can I brand the lid for my shop?

Yes, the lid is a large plain panel. Add your logo or a product name as an engraving layer in your laser software; the download itself contains cut lines only.

Similar files