DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with two sections and a sliding lid pushed half open on a counter, small hot sauce and mustard bottles in the large section and two oil bottles in the small one.Visualization
DW-106027 · UPDATED 11/17/2026

Sliding Lid Box SVG, Hot Sauce Gift Box Laser Cut File, Wooden Condiment Storage Box With Lid DXF

A covered sauce box with two sections and a flat lid that slides in on two rails, made for hot sauce sets, small oil bottles and condiment gifts. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box is 310 × 200 × 80 mm (12.20 × 7.87 × 3.15 in), uses 9 pieces and goes together with tabs and slots.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
310 × 200 × 80 mm (12.20 × 7.87 × 3.15 in)
Parts
9
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,225 × 292 mm
Cut length
7.67 m
Est. time, 10 W diode (3 mm)
25 min 34 s
Est. time, 40 W CO2 (3 mm)
10 min 39 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file for your plywood thickness and cut one rail and a short strip of lid edge first to check the sliding fit.
  2. 02Cut all nine pieces, splitting the long layout across two sheets if your bed is short.
  3. 03Fix the two rails inside the side walls, assemble the walls, divider and base, and fit the low front wall last.
  4. 04Slide the lid in, sand any edge that rubs, then finish and fill the two sections with bottles.

A lid that slides, not hinges

Two thin rails sit along the inside of the side walls and the lid runs between them, entering over a front wall that is cut a little lower (73.7 mm against 80 mm at the back). There is no hinge and no catch: you push the lid back to open it, pull it forward to close. Inside, one divider splits the box into two sections. The photo shows the larger one packed with seven small bottles of chili sauce, mustard and dark sauces, and the smaller one with olive oil and a red vinegar.

Making it on a hobby laser

Nine pieces nest on a layout about 1225 × 292 mm for 3 mm plywood, slightly shorter for thicker stock. Few home lasers take that in one go, so put the lid and base on one sheet and the walls, divider and rails on the next. Expect about 25 min 34 s on a 10 W diode for the 3 mm file, or about 10 min 39 s on a 40 W CO2. Thicker sheets mean more diode passes.

Fix the rails along the inside of the side walls first, level with each other, before the walls go into the base. Then add the back, the divider and the low front, and test the lid. If it binds, a few strokes of sandpaper on its edges free it up.

Gift box ideas

A hot sauce tasting set is the obvious use: fill the big section with five to seven sample bottles and the small one with a matching oil. The plain lid is a good place for a recipient's name, a shop logo or a chili drawing, burned in with your own artwork after cutting. Sellers can offer the box empty or filled, and a stack of them makes a tidy market display.

Questions about this file

How many sauce bottles fit inside?

The pictured box holds seven small 100 ml style bottles in the large section and two slim oil bottles in the small one. Bottles must stay under about 70 mm tall for the lid to close.

Why does the sauce box have a lower front wall?

The lid slides in over the front edge, so the front is cut down to 73.7 mm to leave room for it. The back and sides stay at 80 mm.

The lid is tight in 6 mm plywood, what can I do?

Plywood sheets vary in real thickness. Sand the long edges of the lid lightly, or rub them with candle wax, until it glides along the rails.

Can I add a name or logo to the lid?

Yes, the file only has cut lines, so add your own engraving layer on the lid in your laser software before or after cutting.

Will MDF work instead of plywood?

MDF cuts cleanly and is fine for a gift box that stays dry. For a kitchen box near the sink, birch plywood with a sealed finish lasts longer.

Similar files