VisualizationSliding Lid Box SVG, Hot Sauce Gift Box Laser Cut File, Ten Bottle Tasting Set Holder DXF
A sauce box with a sliding lid and ten slots in two rows of five, sized for small sample or miniature bottles of oil, vinegar and hot sauce. The free download includes SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 370 × 160 × 80 mm (14.57 × 6.30 × 3.15 in), has 13 pieces and assembles with tabs and slots, and the lid slides in on two rails.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 370 × 160 × 80 mm (14.57 × 6.30 × 3.15 in)
- Parts
- 13
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,454 × 406 mm
- Cut length
- 10.71 m
- Est. time, 10 W diode (3 mm)
- 35 min 42 s
- Est. time, 40 W CO2 (3 mm)
- 14 min 53 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file that matches your plywood, cut a short divider and check that it drops into its slot without forcing.
- 02Cut all 13 pieces, splitting the 1454 mm layout over several sheets on a smaller bed.
- 03Build the base, walls and the divider grid, fit the two rails, then slide the lid in to check it runs freely.
- 04Sand the lid edges until it glides, finish with clear lacquer and load ten sample bottles.
A tasting set in one box
Ten slots in two rows of five make this box a natural home for a sauce or oil tasting set. The photo shows six small round bottles in the uncovered part: balsamic, two golden oils, a chilli sauce, a red sauce and a mustard, each in its own slot so they do not knock together in transport. One long divider runs down the middle and four short ones cross it, so every slot is the same size.
The lid is a single 363.4 × 159.7 mm panel that slides in on two narrow rails. There is no hinge and no lock: slide it off to reach the bottles and slide it back to close the box. With the lid on, the set stays clean on a shelf or in a gift bag.
Cutting notes
The 3 mm layout is 1454 × 406 mm, so most diode and desktop CO2 machines will need it split over three sheets. Cutting takes about 35 min 42 s for the 3 mm file on a 10 W diode, about 14 min 53 s on a 40 W CO2 and about 7 min 08 s on a 100 W CO2. Thicker 5 and 6 mm sheets need several diode passes, so a CO2 is the easier route there.
Test the lid before you glue anything. It should move with light pressure; if it binds, a few strokes of sandpaper along its edges fix the fit.
Gift and selling ideas
Fill it with ten miniature hot sauces for a tasting night, pack homemade infused oils for the holidays, or offer it empty at a craft fair as a sampler box for small producers. A logo engraved on the lid turns it into a branded box for a deli or farm shop, and a family name makes it a wedding or housewarming present.
Questions about this file
How big is each of the ten slots?
In the 3 mm version each slot is roughly 70 mm wide and 75 mm deep, which suits miniature and sample bottles like those in the photo.
Does the lid lock?
No. It slides in on two rails and stays put by friction; a ribbon or a paper band holds it closed for shipping.
Can I scale it up for full-size sauce bottles?
Scaling also changes the slot widths, which must match your plywood thickness. Keep it at 100% and raise the walls in a vector editor if you need more height under the lid.
Do I need glue?
The tab-and-slot joints hold together dry. Glue the outer walls if the box will travel full, but keep glue away from the lid and its rails.
Can I put artwork on the lid?
Yes. The file has cut lines only, so add your own picture or text to the lid in your laser software before cutting.
Similar files



