DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood three-step spice stand with four slots per step: glass spice jars on the top two steps and clear spice pouches on the bottom step, on a kitchen counter by a window.Visualization
DW-101063 · UPDATED 11/17/2026

Tiered Spice Rack SVG, Three Step Spice Jar Stand Laser Cut File, Countertop Spice Shelf DXF

A free laser cut file for a tiered spice rack with three steps rising to the back, each step split into four slots by dividers, 12 compartments in total. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the stand measures 320 × 200 × 240 mm (12.60 × 7.87 × 9.45 in) and is built from 18 pieces that join with tabs and slots. Small part numbers are engraved on the pieces to guide assembly.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
320 × 200 × 240 mm (12.60 × 7.87 × 9.45 in)
Parts
18
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,300 × 361 mm
Cut length
11.84 m
Est. time, 10 W diode (3 mm)
39 min 28 s
Est. time, 40 W CO2 (3 mm)
16 min 27 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file for your plywood thickness and test one divider slot on scrap before cutting the whole stand.
  2. 02Cut the 18 pieces, rearranging them onto two or three sheets if your bed is shorter than 1300 mm.
  3. 03Follow the engraved numbers: shelves, step boards and brace into one side, then the front board, the second side and finally the nine dividers.
  4. 04Sand, seal with oil or clear lacquer, and fill the top two steps with jars and the bottom step with pouches.

Every jar in view

A flat drawer hides the jars at the back. This stand lifts them instead: three steps climb toward the back wall, and the tallest point is 240 mm, so the top row sits well above the front. Each step has three thin dividers, giving four slots per level and twelve in all. In the photo the two upper steps hold glass jars with metal lids, and the lowest step holds zip pouches of bay leaves, chili flakes and herbs, which stay upright because the dividers hold them like bookends.

The front board along the lowest step is 72 mm tall, high enough that soft pouches lean back against it instead of sliding off.

Cutting and assembly

The 18 pieces are two sides, a front board, two step boards, three shelves, a brace and nine dividers. For the 3 mm file the layout is 1300 × 361 mm, longer than most diode and desktop CO2 beds, so plan to move the pieces onto two or three smaller sheets. Cutting time for the 3 mm file is about 39 min 28 s on a 10 W diode, about 16 min 27 s on a 40 W CO2 and about 7 min 54 s on a 100 W CO2.

Each piece carries a small engraved number, which helps here because the shelves and step boards look alike. Fit the shelves, step boards and brace into one side, add the front board, close it with the second side, and push the dividers into their slots last. A drop of glue in the side joints keeps the frame square when it is fully loaded.

Where it works

It suits a counter corner or an open shelf, and the 320 mm width matches many cabinet interiors. Makers selling at craft fairs can stock it with twelve filled jars as a ready gift, or sell the bare stand next to a matching pantry tray.

Questions about this file

What size jars fit on each step?

Each slot is roughly a quarter of the 320 mm width, so one standard round jar about 60–70 mm across fits per slot. Taller jars belong on the top step, where nothing sits above them.

What are the small numbers engraved on the stand parts for?

The file engraves small part numbers so you can tell the similar shelves and step boards apart. They are faint and end up mostly hidden once the stand is built.

Is 3 mm plywood strong enough for twelve full jars?

Yes for everyday spice jars, because the brace and step boards stiffen the shelves. Choose 4 or 5 mm if you plan to load heavy glass or oil bottles.

Can I make the stand wider for more slots?

You can stretch it in your editor, but every slot must stay the width of your material, and new divider slots have to be drawn in by hand.

Can it stand near the stove?

Keep it away from direct flame and steam. A couple of coats of clear lacquer protect the plywood from grease and make it easy to wipe.

Similar files