DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood hinged spice box with the lid flipped open, showing four compartments: small glass spice jars on the left and colourful seasoning sachets on the right, on a kitchen counter.Visualization
DW-101033 · UPDATED 11/17/2026

Hinged Box SVG, Wooden Spice Box With Lid Laser Cut File, Four Section Seasoning Chest DXF

A free laser cut file for a hinged spice box whose lid flips open at the back on pins cut into the plywood, with four compartments in two rows of two. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 300 × 180 × 100 mm (11.81 × 7.09 × 3.94 in) and is made of 8 pieces that join with tabs and slots, with no metal hardware.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
300 × 180 × 100 mm (11.81 × 7.09 × 3.94 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,100 × 296 mm
Cut length
7.71 m
Est. time, 10 W diode (3 mm)
25 min 41 s
Est. time, 40 W CO2 (3 mm)
10 min 42 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the file for your plywood thickness and cut one pin and one side panel from scrap to check that the pin turns freely.
  2. 02Cut all eight pieces and mark which side panel is left and which is right.
  3. 03Assemble base, front, back and the first side, slip the lid pins into its hole, close with the second side, then cross the two dividers inside.
  4. 04Sand the lid edges, open and close it a few times, oil the box and load the four compartments.

A spice chest that opens like a jewellery box

The lid is one 300 × 176.3 mm panel that turns on two small pins at the back. The pins are part of the plywood itself, held in holes in the two side panels, so you do not need metal hinges, screws or a drill. Lift the front edge and the lid swings up and rests open, as in the photo.

Two crossing dividers split the inside into four equal compartments, each about 145 mm wide and 85 mm deep. In the photo the two on the left hold four small spice jars each, and the two on the right keep flat seasoning sachets sorted by colour. Because the box is 180 mm deep, it also takes taller jars than a drawer insert would.

Thickness and cutting time

The eight pieces are a front, a back, two side panels with the pin holes, a base, one long and one short divider, and the lid. The 3 mm layout is 1100 × 296 mm, which still needs splitting on most 400 mm diode beds but fits many larger CO2 machines in one go. For the 3 mm file, plan on about 25 min 41 s with a 10 W diode, about 10 min 42 s with a 40 W CO2 and about 5 min 08 s with a 100 W CO2.

The pins turn most smoothly in 3 or 4 mm birch. In 6 mm the lid becomes heavy, so test the swing before gluing anything.

Finishing touches

Keep glue away from the pins and the lid edge. Sand the inner corners of the lid where it brushes the sides, then oil the outside. A carved-look engraving of herbs on the lid, added yourself, turns it into a wedding or housewarming present.

Questions about this file

Does the hinged lid need metal parts?

No. The lid pivots on pins cut into the plywood that sit in holes in the side panels, so the whole box is wood.

What can I store in the four compartments?

Each one is about 145 × 85 mm: four small spice jars, a row of seasoning sachets, bouillon cubes or tea bags all fit.

The lid rubs on the sides. How do I fix it?

Sand the lid's side edges a little until it swings freely. Varnish adds thickness, so finish first and sand afterwards.

Should I glue the box together?

Glue the base and corner joints if you like, but leave the lid and its pins dry so the hinge keeps moving.

Can this hinged box be made in MDF?

It can, using the file that matches the MDF thickness. Plywood holds the small pins better over years of opening and closing.

Similar files