DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood spice box with a sliding lid pushed partly over the right side, revealing compartments of small glass spice jars and colourful seasoning sachets, on a wooden kitchen table.Visualization
DW-101023 · UPDATED 11/17/2026

Sliding Lid Box SVG, Spice Storage Box Laser Cut File, Six Compartment Seasoning Box DXF

A free laser cut file for a spice box with a sliding lid and six compartments laid out in three columns and two rows. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 340 × 160 × 100 mm (13.39 × 6.30 × 3.94 in) and consists of 11 pieces that lock together with tabs and slots, with the lid running on two rails.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
340 × 160 × 100 mm (13.39 × 6.30 × 3.94 in)
Parts
11
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,364 × 332 mm
Cut length
9.39 m
Est. time, 10 W diode (3 mm)
31 min 18 s
Est. time, 40 W CO2 (3 mm)
13 min 03 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Select the file for your plywood thickness and cut a single slot plus a rail on scrap to confirm the fit.
  2. 02Cut the 11 pieces, splitting the long layout across sheets if needed, and keep the lid panel flat while it cools.
  3. 03Build the base, back, sides and front, fit the two rails and test the lid, then set the long divider and both short dividers.
  4. 04Sand the lid edges until it slides freely, rub on wax or oil, and fill the six compartments.

A closed box for a busy counter

Open trays collect dust and kitchen grease; this one closes. The lid is a flat panel that slides in on two rails, so there is no hinge to wear out and nothing sticks out when it is shut. Slide it partway and you uncover only the compartments you need, as in the photo, where the right-hand third is still covered.

Inside, one long divider and two short ones make six compartments, three across and two deep, each roughly 110 mm wide. The left pair takes small jars three abreast, while the middle and right pairs suit seasoning sachets, stock cubes or tea-style spice bags stood on edge. With 100 mm of height, sachets stay below the lid line.

Making it

The 11 pieces are the front, back, two sides, base, two short dividers, a long divider, two narrow rails and the lid. Fit the rails before the dividers go in, while you can still reach them, and check that the lid runs straight before you add any glue.

The 3 mm layout measures 1364 × 332 mm, so on a smaller bed spread the parts over two or three sheets. For the 3 mm file, cutting takes about 31 min 18 s on a 10 W diode, about 13 min 03 s on a 40 W CO2 and about 6 min 16 s on a 100 W CO2. Wax the rail edges lightly if the lid feels tight after finishing.

Gift idea

The plain lid is a blank canvas. Engrave a monogram or a pepper sprig on it yourself, fill the six compartments with blends, and you have a hostess gift that also sells well at holiday markets.

Questions about this file

What keeps the sliding lid in place?

It slides in on two narrow plywood rails and rests on them. There is no lock, so the box should be carried level when full.

What fits in each of the six compartments?

Each one is about 110 mm wide and 75 mm deep, enough for three small spice jars or a stack of seasoning sachets standing upright.

Can I cut the sliding lid from clear acrylic?

Yes, a 3 mm acrylic lid lets you see the contents. Cut the box itself from plywood and make sure the acrylic is the same thickness the rails expect.

The lid sticks after varnishing. What can I do?

Finish adds thickness to the edges. Sand the lid edges and the rails lightly, then rub a bit of beeswax on them.

Can I enlarge it for bigger jars?

Edit the box in a vector program rather than scaling it, because the slots and rails must still match your material thickness.

Similar files