Visualization3 Tier Spice Riser SVG, Nine Slot Stepped Spice Stand Laser Cut File, Wooden Spice Jar Steps DXF
A free laser cut file for a three-tier spice riser: three steps climb toward the back and two short dividers split every step into three slots, nine in total. It stands 380 × 240 × 180 mm (14.96 × 9.45 × 7.09 in), is cut from 15 plywood pieces that join with tabs and slots, and small part numbers are engraved on the pieces to guide assembly. Separate SVG and DXF versions are included for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 380 × 240 × 180 mm (14.96 × 9.45 × 7.09 in)
- Parts
- 15
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,540 × 328 mm
- Cut length
- 11.87 m
- Est. time, 10 W diode (3 mm)
- 39 min 34 s
- Est. time, 40 W CO2 (3 mm)
- 16 min 29 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and test one divider in a scrap slot before cutting the whole stand.
- 02Cut the 15 numbered pieces over as many sheets as your bed needs and keep each shelf with its divider pair.
- 03Join the two stepped sides with the bottom shelf and front board, add the middle and top shelves with their step boards, fit the rear brace, then press two dividers into every shelf.
- 04Round over the step lips with fine sandpaper, seal the stand with oil, and arrange jars on the top and bottom steps with pouches in the middle.
Nine slots on three steps
At 18 cm tall this is the highest riser in the spice range, built for a counter or a deep pantry shelf where jars at the back usually disappear. Each step is a shelf with a low lip in front of it, and two dividers per step make three equal slots, so jars stay lined up instead of sliding together. The bottom shelf is 97 mm deep, the two upper shelves 89.4 mm, and a brace across the back holds the stepped sides square.
The photo shows how to mix containers by level. The bottom step carries three clip-top glass jars with pink salt, coriander seed and bay leaves. The middle step holds three stand-up pouches of oregano, turmeric and paprika, leaning back so their windows face you. Three bamboo-lidded jars of peppercorns, dried herbs and chili flakes sit on the top step.
Before you cut
There are 15 pieces: two stepped sides, a front board, two step boards, three shelves, the brace and six dividers. Cutting time for the 3 mm file is about 39 min 34 s with a 10 W diode, about 16 min 29 s on a 40 W CO2 and about 7 min 55 s on a 100 W CO2. The layout is 1540 × 328 mm, so on a hobby bed spread it over three sheets: sides first, then the 380 mm boards and shelves, then the brace and dividers. The engraved numbers keep the near-identical shelves in order. A diode cuts 3 mm in one or two passes; 5–6 mm takes several passes or a CO2.
Who will use it
A filled riser makes a solid wedding or housewarming present. Small spice brands can stand one on a shop counter with three blends per step, and cafes can use the slots for syrups or sugar jars.
Questions about this file
What size jars fit the slots?
The photo shows round jars roughly 9 cm across, one per slot, on the bottom and top steps. Stand-up spice pouches fit the middle step and lean against the step behind.
How thick should the plywood be for this riser?
4 mm is a good middle choice for glass jars, as the shelves span 380 mm between the sides. 3 mm works for pouches and light jars, 5 or 6 mm for heavy clip-top jars.
Why can I not just scale it to 300 mm wide?
Scaling changes every slot width along with the outline, so tabs no longer fit your sheet. Shorten the shelves, boards and brace in the drawing instead and keep each slot equal to the material thickness.
What do the small engraved numbers do?
Each piece carries its part number so you can tell the three shelves and the two step boards apart. Apart from those numbers, the riser is cut lines only.
Can I brand the sides for my shop?
The stepped side panels have a large flat area, so you can add your logo there as an extra engrave layer before cutting.
Similar files



