VisualizationCutlery Box With Removable Lid SVG, Dustproof Silverware Storage Laser Cut File, Lidded Utensil Grid Box DXF
A free laser cut file for a cutlery box with a separate lift-off lid and six cells in two columns of three, 260 × 320 × 70 mm (10.24 × 12.60 × 2.76 in) outside. The download provides SVG and DXF for 3, 4, 5 and 6 mm plywood, and the 9 pieces, lid included, join with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 320 × 70 mm (10.24 × 12.60 × 2.76 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,180 × 726 mm
- Cut length
- 11.26 m
- Est. time, 10 W diode (3 mm)
- 37 min 31 s
- Est. time, 40 W CO2 (3 mm)
- 15 min 38 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the SVG or DXF for your sheet thickness and cut one cross slot on scrap to check the divider fit.
- 02Cut the 9 pieces, placing the base and the lid on different sheets if your bed is under 726 mm deep.
- 03Assemble the base and four walls, lock the long divider and two cross dividers together inside, and check the lid drops on squarely.
- 04Sand the lid edges, oil the box inside and out, and fill the cells before setting the lid on top.
Storage that stays dust-free
This box is meant for cutlery you do not use every day: the guest set, the party teaspoons, the camping spares that live on a high shelf. The lid is a flat 260 × 320 mm panel the same size as the box, so it simply sits on top and lifts straight off with no rails or pins to wear. Stack a second box on it and the pair still takes up one footprint.
Inside, a long divider and two cross dividers make six cells of roughly 12.5 × 10 cm on 3 mm plywood. The dividers are 67 mm tall, just under the walls, so the lid rests on the walls and not on the contents. Teaspoons, dessert forks, butter knives, cocktail picks and napkin rings sort neatly into them. The photo shows the left column opened into a single long bay for dinner forks; to copy that, trim both cross dividers to the right column in your editor before cutting.
Cutting and fitting
The 3 mm file needs about 37 min 31 s on a 10 W diode, about 15 min 38 s on a 40 W CO2 and about 7 min 30 s on a 100 W CO2. The layout is 1180 × 726 mm, so on a desktop laser put the base and lid on separate sheets. Thicker plywood (5 or 6 mm) gives a lid that will not warp, but a diode will need several slow passes.
Finish and presentation
Sand the lid so it drops on without catching, round its corners slightly by hand, and finish with clear oil. A strip of felt under the lid edge quiets it on a stone counter. If you sell these, an engraved monogram or a simple border on the lid, added by you, turns a storage box into a gift.
Questions about this file
Is the lid of this box hinged or locked?
No. It is a separate panel that rests on the walls and lifts off, so carry the box with both hands.
Can I stack two boxes?
Yes. The lid is the same size as the box, so a second box sits flat on top of the first.
How big are the cells?
About 12.5 × 10 cm each on 3 mm plywood. That suits teaspoons, cake forks and small spoons; long knives need one column opened into a long bay.
Is acrylic a good choice for the lid?
A clear acrylic lid of the same thickness lets you see what is inside. Cut the walls in plywood and only the lid in acrylic.
How do I stop the lid warping?
Use flat, good-quality birch plywood and finish both faces of the lid equally so it takes up moisture evenly.
Similar files



