VisualizationBook Style Spice Box SVG, Living Hinge Spice Case Laser Cut File, Wooden Book Box DXF, Spice Book Box
A free laser cut file for a long book-style spice box whose cover wraps over the top like a book cover, bending on a flexible living-hinge spine made of thin kerf cuts. It measures 400 × 180 × 90 mm (15.75 × 7.09 × 3.54 in), has one open compartment, and is cut from 7 plywood pieces that join with tabs and slots. There is an SVG and a DXF for each plywood thickness: 3, 4, 5 and 6 mm.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 400 × 180 × 90 mm (15.75 × 7.09 × 3.54 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 2,055 × 188 mm
- Cut length
- 16.99 m
- Est. time, 10 W diode (3 mm)
- 56 min 39 s
- Est. time, 40 W CO2 (3 mm)
- 23 min 36 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood, ideally 3 or 4 mm birch, and cut a test strip of the hinge pattern to check it bends without cracking.
- 02Cut the long cover on a large enough bed in one piece, then the front, back, two sides and the pin.
- 03Assemble the box walls first, then bend the cover slowly around the spine, warming it slightly if it feels stiff, and seat its tabs.
- 04Sand gently around the hinge area, wipe on a thin oil rather than thick lacquer so the spine stays flexible, and fill the compartment.
A spice box that opens like a book
The long cover is one piece. A band of fine parallel cuts lets it bend round the back of the box like the spine of a hardback, so it opens up and folds back without any hinge hardware. Closed, the box looks like a thick wooden book lying on the counter, 40 cm long and 9 cm high.
Inside there is one open compartment. In the photo it is fitted with simple separators: four pairs of small square jars along the back (peppercorns, herbs, chili flakes, turmeric) and rows of flat seasoning packets in front. Those separators are not part of this file; cut a few strips from offcuts if you want the same layout, or leave the space open for larger jars.
Cutting the flex cover
The flex spine bends best in good-quality birch plywood with no voids; cheap poplar ply tends to crack along the cuts. The cover is 846.7 mm long and cannot be split, so the 3 mm layout is a strip 2055 × 188 mm and you need a bed at least about 850 mm long for that piece. The other parts (front, back, two long sides and a small pin) fit on any bed. Cutting time for the 3 mm file is about 56 min 39 s with a 10 W diode, about 23 min 36 s on a 40 W CO2 and about 11 min 20 s on a 100 W CO2; the hinge lines account for much of it. Thin 3 or 4 mm plywood flexes far more easily than 6 mm.
Gift ideas
Engrave a title on the cover, such as a family name and "Spices", to make it look like a cookbook on the shelf. It suits a wedding gift, or a seller can offer it as a premium box for a set of eight blends.
Questions about this file
Do I need a large laser for this box?
Yes, for the cover. It is about 847 mm long in one piece, so the bed must take a strip that long; all other parts are small.
Which plywood bends best for the flex spine?
Void-free birch plywood in 3 or 4 mm. Thicker or lower-grade sheets are stiffer and can split along the kerf cuts.
Are the jar dividers from the photo included?
No, the file cuts one open compartment. Add your own separators from offcuts if you want rows for jars and packets.
Can I make the box shorter?
Shortening means editing the drawing, since the cover length is matched to the walls. Do not scale it, or the slots and hinge spacing change.
How do I finish the flexible cover?
Use a thin penetrating oil or wax. A hard, thick lacquer can crack where the spine bends.
Similar files



