VisualizationBuffet Cutlery Riser SVG, 12 Bin Silverware Display Laser Cut File, Catering Flatware Stand DXF
A free laser cut file for a three-tier buffet cutlery riser with twelve bins, four on each step, 380 × 360 × 180 mm (14.96 × 14.17 × 7.09 in) outside. The download contains SVG and DXF files for 3, 4, 5 and 6 mm plywood; its 18 pieces join with tabs and slots and carry small engraved part numbers to make assembly easier.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 380 × 360 × 180 mm (14.96 × 14.17 × 7.09 in)
- Parts
- 18
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,546 × 403 mm
- Cut length
- 14.84 m
- Est. time, 10 W diode (3 mm)
- 49 min 27 s
- Est. time, 40 W CO2 (3 mm)
- 20 min 36 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and cut a single shelf slot on scrap to confirm the fit before running the full job.
- 02Cut all 18 numbered pieces, grouping the two tall sides on one sheet and the shelves and dividers on the next.
- 03Fix the shelves, step boards, front board and brace into one side, add the second side, then press in the nine dividers row by row.
- 04Sand the shelf edges, apply a food-safe lacquer, and load each tier with forks, spoons, knives and napkins.
Built for self-service counters
Three shelves climb toward the back like stadium seats, and three short dividers on each shelf split it into four bins, twelve in total. Each bin is roughly 9 cm wide, so guests can see every handle from the front and take a fork without reaching over the knives. In the photo the rows hold forks, soup spoons and knives, with a glass of toothpicks, a bundle of chopsticks and folded paper napkins tucked into the end bins.
That makes it a good fit for a hotel breakfast room, a cafe pick-up point, a catering table or a family buffet at home. A small business can keep one riser per station and engrave its logo on the tall side panels; that decoration is something you add, since the file itself carries only cut lines and part numbers.
Cutting it on a hobby laser
The 3 mm file runs about 49 min 27 s on a 10 W diode, about 20 min 36 s on a 40 W CO2 and about 9 min 53 s on a 100 W CO2. The full layout measures 1546 × 403 mm, so on a smaller bed you will cut the two sides on one sheet and the shelves, boards and dividers on others. For a stand that carries heavy stainless cutlery all day, 4 or 5 mm plywood is stiffer; a 10 W diode needs several passes for those.
Putting the tiers together
Lay one side flat, then slot in the three shelves, the two step boards, the front board and the brace before closing with the second side. Push the dividers in last. The engraved numbers show where each piece goes. Glue is optional, but a commercial counter gets knocked a lot, so a few drops on the shelf joints are worth it. Seal everything with a food-safe lacquer so wet cutlery from the dishwasher does not mark the wood.
Questions about this file
How much cutlery does each bin hold?
A bin about 9 cm wide takes roughly 15 to 20 forks or spoons standing at an angle, which is enough for a busy breakfast service between refills.
Why are small numbers marked on each riser piece?
Each piece has a small engraved part number that matches the assembly order, so shelves and dividers of similar size do not get mixed up.
Can I put our cafe logo on it?
Yes. Add your logo as an engrave layer on the side panels or the front board in your laser software before cutting.
Is 3 mm plywood strong enough for a restaurant?
It works for home use and light service. For a stand that works every day in a cafe, choose 4 or 5 mm and glue the shelf joints.
How do I clean it after service?
Wipe the bins with a damp cloth and dry them at once. A lacquered or oiled finish keeps spills from soaking into the plywood.
Similar files



