DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Long light birch plywood tea chest with its flat lid leaning behind it, four tins of loose tea in the back row and upright tea bags in four front bays, on a wooden kitchen table.Visualization
DW-102045 · UPDATED 11/21/2026

8 Bay Lidded Tea Chest SVG, Long Narrow Tea Storage Box Laser Cut File, Lift Off Lid Tea Bag Organizer DXF

A free lidded tea chest laser cut file in SVG and DXF, with separate versions for 3, 4, 5 and 6 mm plywood. The chest is 380 × 160 × 90 mm (14.96 × 6.30 × 3.54 in), long and narrow, with 8 bays in two rows of four. It is cut as 10 pieces that join with tabs and slots, and a separate flat lid sits on top and lifts straight off.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
380 × 160 × 90 mm (14.96 × 6.30 × 3.54 in)
Parts
10
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,484 × 332 mm
Cut length
11.77 m
Est. time, 10 W diode (3 mm)
39 min 13 s
Est. time, 40 W CO2 (3 mm)
16 min 21 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the file for your plywood thickness and cut one corner joint on scrap to check the fit.
  2. 02Cut the 10 pieces: four walls, base, one long divider, three short dividers and the flat lid, over two or three sheets if needed.
  3. 03Fit the walls to the base, cross the long divider with the three short ones, and check that the lid sits flat on all four walls.
  4. 04Sand the lid edges and the rim, finish with oil or lacquer, then put tins in the back bays and tea bags in front.

Long and slim for a shelf edge

At only 160 mm deep, this chest is made for a narrow shelf, a window ledge or the gap between a kettle and the wall. Four walls of the same 90 mm height enclose a grid of one long divider and three short ones. In the photo the back row holds four round tins of loose tea: black, jasmine pearls, hibiscus and a green blend. The front row has tea bags packed upright in long rows of white, green, yellow and red. Every divider sits a little below the rim, so the lid rests flat on the walls.

The lift-off lid

The lid is one flat 380 × 160 mm panel that sits on top of the walls. Nothing holds it, so you lift it off and set it aside, or lean it behind the box as the photo shows. That makes it a very easy lid to cut and fit. If you want it to stay put, glue a frame of thin strips to its underside, just inside the walls.

For the 3 mm file the cut lasts about 39 min 13 s on a 10 W diode, about 16 min 21 s on a 40 W CO2 and about 7 min 51 s on a 100 W CO2. The layout runs 1484 × 332 mm, so plan two or three sheets on any bed shorter than that; the lid, base, front, back and long divider each need about 380 mm of length. A diode cuts the 3 mm version in one or two passes, while 6 mm wants a CO2 tube.

Ideas

Fill it with eight teas for a tasting evening, engrave a family name on the lid, or sell it at a market as a box for tea collectors. Seal it with clear oil to bring out the birch grain.

Questions about this file

Does the lid lock or click in place?

No, it is a plain flat lid resting on the walls. Glue thin strips under it if you want it to locate itself.

How wide is each bay of the chest?

About 9 cm across and 7.5 cm front to back, which takes a round tin of up to about 7 cm or a row of tea bags.

Could the chest lid be cut from acrylic?

Yes, a clear 3 mm acrylic lid lets you see the teas inside; keep the box itself in plywood with the matching file.

Is 4 mm better than 3 mm for this long chest?

4 mm makes the 380 mm walls stiffer, which helps on a box this long; 3 mm is lighter and quicker to cut on a diode.

Will it keep loose tea fresh?

The lid keeps out light and dust but is not airtight, so store loose tea in its own sealed tins inside the bays.

Similar files