VisualizationHinged Flatware Gift Box SVG, Narrow Silverware Keepsake Case Laser Cut File, Pin Hinge Cutlery Box DXF
A free laser cut file for a narrow flatware gift box with six cells and a lid that flips open on pins cut into the plywood, 240 × 340 × 70 mm (9.45 × 13.39 × 2.76 in) outside. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; its 9 pieces assemble with tabs and slots, and there are no metal hinges or screws.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 340 × 70 mm (9.45 × 13.39 × 2.76 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,324 × 426 mm
- Cut length
- 9.37 m
- Est. time, 10 W diode (3 mm)
- 31 min 15 s
- Est. time, 40 W CO2 (3 mm)
- 13 min 01 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood and cut the pin joint on scrap to check that the lid pivots freely.
- 02Cut all 9 pieces, keeping the lid and the two tall side panels on the same sheet for a matching thickness.
- 03Build the base, back and lower front, interlock the dividers, then fit the sides and lid so the pins engage as you close the box.
- 04Sand the lid edges until it swings smoothly, engrave a name if you like, oil the box and line the cells with felt.
A slim box with a flip-up lid
At only 24 cm wide it slips onto a bookshelf or into a sideboard where a full cutlery chest will not fit. A long divider and two cross dividers form six cells, two columns of three, each roughly 11.5 × 11 cm inside on 3 mm plywood. Those cells suit small treasures rather than a dinner service: christening spoons, a baby cutlery set, souvenir spoons, silver teaspoons or cake forks from a wedding.
The lid pivots at the back on pins cut into the plywood, and the side panels stand 74.2 mm tall, a little above the back wall. The front wall is a little lower, at 67 mm, so the lid closes flat. The photo shows the left column as one long bay for forks and spoons; the file has full-width cross dividers, so trim them to one column in your editor if you want that layout.
Cutting notes
Cutting the 3 mm file takes about 31 min 15 s on a 10 W diode, about 13 min 01 s on a 40 W CO2 and about 6 min 15 s on a 100 W CO2. The layout is 1324 × 426 mm; the lid (240 × 336.3 mm) and base are the two biggest parts, so plan two or three sheets on a smaller bed. Test the pin fit on scrap first: the lid should swing freely without dropping out.
Making it a keepsake
The plain lid is where a gift becomes personal. Add your own engraving, such as a baby's name and birth date, a wedding date or a family initial. Line the cells with felt to stop silver from scratching, and finish the outside with oil or a satin lacquer.
- A christening or baptism gift holding a first spoon and fork
- A box for a collection of travel souvenir spoons
- Matching boxes for bridesmaids with a cake fork and teaspoon each
Questions about this file
How does the lid stay attached without hinges?
It turns on pins cut from the plywood itself at the back of the box. No metal hardware is needed.
What size of spoon fits one cell of this gift box?
Each cell is about 11.5 × 11 cm, so teaspoons, baby spoons, souvenir spoons and cake forks lie flat. Dinner cutlery is too long unless you open up one column into a long bay.
Can a baby name or date go on the flip lid?
Yes, add a text layer to the lid in your laser software before cutting, since the download carries no engraving of its own.
The lid binds when I open it. What helps?
Sand the back edge of the lid slightly and rub a little wax on the pins. Swollen plywood in a humid room is the usual cause.
Can I scale it down for a single spoon?
Reduce the outer size in your editor but keep every slot and pin hole matched to your plywood thickness, or the box will not hold together.
Similar files



