DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Large birch plywood book-style cutlery case open on a stone kitchen island, its flexible spine curving up at the left end, with forks, spoons, knives, chopsticks and teaspoons laid in lanesVisualization
DW-104055 · UPDATED 11/21/2026

Book Box Cutlery Case SVG, Living Hinge Flatware Box Laser Cut File, Large Silverware Book Box DXF

A free laser cut file for a large book-style cutlery case, 400 × 300 × 60 mm (15.75 × 11.81 × 2.36 in) outside, with one open compartment and a cover that wraps from the base up around one short end and over the top, like a book binding. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; the file lists 7 parts (front, back, two sides, the long wrap-around cover, its flex-cut spine pattern and a small pin), assembled with tabs and slots.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
400 × 300 × 60 mm (15.75 × 11.81 × 2.36 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
2,278 × 308 mm
Cut length
18.34 m
Est. time, 10 W diode (3 mm)
61 min 08 s
Est. time, 40 W CO2 (3 mm)
25 min 28 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the 3 or 4 mm file for an easy-bending spine, and cut a small section of the kerf pattern on scrap to check that it flexes without breaking.
  2. 02Cut all the parts, making sure your bed takes the 829.5 mm long cover in one piece.
  3. 03Fit the front, back and two sides onto the base end of the cover, then bend the spine gently up and over the top and set the small pin.
  4. 04Sand the edges, oil the box and the spine lightly, and fill the open compartment or add your own divider strips.

How the book cover works

The base, spine and top are a single long piece, 829.5 × 300 mm. A band of thin parallel kerf cuts turns part of that strip into a flexible spine, so the cover bends up around one 30 cm end of the box and folds over the top like the cover of a hardback. The front, back and two sides stand on the base and give one roomy open compartment, almost the full 40 × 30 cm footprint. The spine bends best in good-quality birch plywood with no voids; cheap poplar or MDF tends to crack along the cuts.

In the photo the case holds a full set laid out in lanes, with forks, spoons, knives and chopsticks in four bays and teaspoons in a strip along the front. Those divider strips are not part of the file. Leave the box open for serving pieces and a cloth cutlery roll, or glue in your own strips from offcuts to match your set.

Check your bed size first

Because the cover is one piece, you need a laser bed at least 830 × 300 mm, or a pass-through slot. The whole 3 mm layout is 2278 × 308 mm. Cutting the 3 mm file takes about 61 min 08 s on a 10 W diode, about 25 min 28 s on a 40 W CO2 and about 12 min 14 s on a 100 W CO2; most of that time is the dense spine pattern. Thicker plywood makes the spine much stiffer, so 3 or 4 mm is the sensible choice here.

A gift that looks like a book

The flat cover takes an engraved title well, added by you: a family name, "Sunday Dinner" or a wedding date. Finish with oil rather than a thick lacquer, which can crack where the spine flexes. It makes a handsome anniversary present or a storage case for inherited silver that lives on a bookshelf.

Questions about this file

Can my diode laser cut the long cover?

Only if its working area is at least 830 × 300 mm or it has a pass-through. The cover cannot be split because the spine has to be continuous.

Why does the spine crack?

Usually the plywood is too thick, too dry or has hidden voids. Use 3 mm birch, bend it slowly, and warm it slightly with a hair dryer if it feels stiff.

Are dividers included?

No. The cutlery case comes as one open space, so glue in offcut strips if you want lanes like those in the photo.

Would the book box work in acrylic?

Not the cover, since acrylic snaps instead of flexing at the kerf cuts. The walls could be acrylic with a plywood cover.

What finish suits the flexible spine?

A thin oil or wax. Hard lacquer forms a skin that can crack each time the cover opens.

Similar files