DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood spice organizer with three compartments: two rows of glass spice jars on the left and colored seasoning packets standing upright on the right, on a sunny kitchen counter with basil.Visualization
DW-101003 · UPDATED 11/17/2026

Spice Jar Organizer SVG, Seasoning Packet Holder Laser Cut File, Sloped Kitchen Tray DXF

A free laser cut file for an open spice organizer that keeps glass jars in two rows on the left and seasoning packets upright in one wide bay on the right. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 300 × 160 × 100 mm (11.81 × 6.30 × 3.94 in) and is made from 7 pieces with 3 compartments. The front wall is lower and the sides slope down to it, and everything joins with tabs and slots.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
300 × 160 × 100 mm (11.81 × 6.30 × 3.94 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
940 × 272 mm
Cut length
4.91 m
Est. time, 10 W diode (3 mm)
16 min 22 s
Est. time, 40 W CO2 (3 mm)
6 min 49 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the SVG or DXF that matches your plywood thickness and cut a single wall corner first to check how tight the tabs feel.
  2. 02Cut all 7 parts, splitting the layout across smaller sheets if your bed is shorter than 940 mm.
  3. 03Set the long divider into the base, slide the short cross divider into the left half, then fit the back, sloped sides and low front.
  4. 04Sand the edges, oil or lacquer the tray, and load jars on the left and packets on edge in the right bay.

Jars on one side, sachets on the other

This tray solves a common kitchen mix: a handful of small glass jars plus a growing pile of paper or foil spice packets. One long divider runs front to back and splits the box roughly in half. The left half gets a short cross divider, so it holds two rows of jars, three standard round jars per row in the photo. The right half stays open as one deep bay where flat packets stand on edge like files in a drawer, so you flip through them instead of digging.

The back wall is 100 mm tall and the front only 55 mm, with the side panels cut on a slope between them. Jar lids in the front row sit above the front edge, which makes labels easy to read from the counter.

Cutting it

All 7 parts fit on a layout 940 × 272 mm long, so on a small diode bed you will need to split the pieces across two or three sheets. Estimated cutting time for the 3 mm file is about 16 min 22 s on a 10 W diode, about 6 min 49 s on a 40 W CO2 and about 3 min 16 s on a 100 W CO2. Thicker files take longer; 5 or 6 mm stock on a diode usually needs extra passes.

Press the divider into the base first, then add the cross divider on the left before the outer walls close the box. The joints hold by friction, and a little wood glue in the corner tabs makes the tray permanent.

Finishing and gift ideas

Sand the cut edges lightly and wipe on a food-safe oil or clear lacquer so cooking splashes wipe off. Filled with six jars and a few packets of your own blends, it makes a good housewarming present. Etsy sellers can offer it bare or stocked, and a matching second tray turns into a neat pantry set.

Questions about this file

How many spice jars fit in the left half?

The photo shows three small round jars in each of the two rows, so six in total. Jars around 45–50 mm across fit that way; wider jars will fit two per row.

Can the right bay hold something other than packets?

Yes. It is one open bay about half the box wide, so tea bags, bouillon cubes or a small grater fit as well as seasoning sachets.

Is it possible to scale this jar and packet tray up for a bigger cabinet?

You can scale the outer size, but the slots must stay as wide as your sheet is thick. Scale the drawing, then correct the slot width, or the tabs will not fit.

Will MDF or acrylic work instead of plywood?

MDF cuts cleanly at the same thickness but dislikes damp kitchens unless it is sealed. Acrylic works too if you measure its real thickness and pick the closest file.

Does the file include any engraving?

No, it contains cut lines only. If you want a label such as a family name on the back wall, add your own engraving layer before cutting.

Similar files