DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood spice box with its lift-off lid leaning behind it, three sections with small spice jars, seasoning packets and herb pouches on a kitchen counterVisualization
DW-101041 · UPDATED 11/16/2026

Spice Box With Lid SVG, Lift Off Lid Storage Box Laser Cut File, Seasoning Packet Box DXF

A free laser-cut file for a three-section spice box with a separate lift-off lid that rests on top. The box is 260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in), uses 8 plywood pieces that fit together with tabs and slots, and comes as SVG and DXF with separate versions for 3, 4, 5 and 6 mm plywood.

Author
DXF World · 281 files
Formats
SVG, DXF
Outer size (W × D × H)
260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in)
Parts
8
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
860 × 252 mm
Cut length
7.58 m
Est. time, 10 W diode (3 mm)
25 min 16 s
Est. time, 40 W CO2 (3 mm)
10 min 32 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Download the file for your plywood thickness and confirm the tab fit with a single test slot.
  2. 02Cut the eight parts, using two passes on separate sheets if your bed cannot take 860 mm.
  3. 03Join the base, front, back and both end walls, then slide the two dividers into their slots and rest the lid on the rim.
  4. 04Sand the lid edges so it lifts off easily, apply your finish and fill each section.

Three sections, one simple lid

This is the most basic lidded version of a spice box: a straight-walled tray with two dividers and a flat 260 × 160 mm lid that sits on top. Lift it off, lean it against the wall behind the box while you cook, and put it back when you are done. The photo shows the left section filled with six small jars of peppercorns, herbs, paprika and curry, the middle section with colourful single-serve seasoning packets, and the right section with flat herb pouches and stock packets. The dividers are slightly lower than the walls, so the lid lies flat on the rim and does not rock.

Cutting the eight pieces

The 3 mm file lays everything out on 860 × 252 mm. If your bed is narrower, put the lid and base on one pass and the four walls with the dividers on the next. Expect about 25 min 16 s on a 10 W diode, about 10 min 32 s on a 40 W CO2 and about 5 min 03 s on a 100 W CO2 for the 3 mm file. A 10 W diode gets through 3 mm in one or two passes; plywood of 5 or 6 mm wants a stronger machine or several passes.

Put the base, back, front and both ends together, slide the dividers in, and try the lid. The joints hold dry, so glue is only needed if you want the box to stay square for years.

Selling and gifting

  • A lid gives you a clean surface for a café or deli logo, so small shops can sell filled boxes at the counter.
  • Make a matching tea box from the same file for a two-piece kitchen set.
  • Finish with oil inside and lacquer on the lid to keep it looking new.

Questions about this file

Does the lid stay in place when the box is carried?

It rests on the rim and is held only by its weight, so carry the box level. For a lid that cannot fall off, choose a hinged or sliding version.

How many jars fit in the jar section?

The photo shows six small jars in two rows of three. Larger jars will fit fewer.

Can I brand the lid for a shop?

Yes. Add your logo as an engraving layer on the lid before cutting; the download itself contains only cut lines.

Is the lid a tight fit?

It sits on top rather than pressing in, so finish thickness does not make it jam. Sand the edges smooth so it lifts off cleanly.

Which wood finish works on the lid?

Clear water-based lacquer keeps the light birch colour and wipes clean. Food-safe oil gives a warmer tone.

Similar files