VisualizationTen Compartment Cutlery Box SVG, Two Row Sliding Lid Silverware Chest Laser Cut File, Teaspoon Sorting Box DXF
A free laser cut file for a ten compartment cutlery box with a sliding lid, 340 × 320 × 70 mm (13.39 × 12.60 × 2.76 in) outside, its cells arranged in two rows of five. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; the 13 pieces join with tabs and slots, and the lid slides in along two rails with no hinge or lock.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 320 × 70 mm (13.39 × 12.60 × 2.76 in)
- Parts
- 13
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,340 × 790 mm
- Cut length
- 14.40 m
- Est. time, 10 W diode (3 mm)
- 48 min 01 s
- Est. time, 40 W CO2 (3 mm)
- 20 min 00 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood thickness and cut a rail and a lid corner on scrap to check that the lid slides without sticking.
- 02Cut all 13 pieces over several sheets, keeping the lid and the two rails together on one.
- 03Assemble the base, back, sides and lower front, slot the four long dividers onto the cross divider inside, then glue the rails along the side walls.
- 04Sand and wax the lid edges, finish the box with oil, sort the small cutlery into the ten cells and slide the lid closed.
Ten narrow cells for sorting
Four long dividers and one cross divider split this box into ten cells, five in the back row and five in the front. Each cell is narrow and deep, roughly 6.5 cm wide and 15.5 cm from front to back inside on 3 mm plywood. That shape is ideal for sorting a set by type: teaspoons, coffee spoons, cake forks, cocktail forks, butter spreaders, sugar spoons and chopstick rests each get their own slot, so a dozen of each stand in a tidy row.
Full-size dinner forks and knives, at 20 cm or more, are longer than one cell, so for a dinner service pick a tray with long lanes and keep this box for the small pieces.
The lid is a flat 333.4 × 319.7 mm panel that slides over the dividers on two rails. The dividers are 60.7 mm tall and the front wall 63.7 mm, both lower than the 70 mm back, which leaves room for the lid to run.
Cutting it
The 3 mm file runs about 48 min 01 s on a 10 W diode, about 20 min 00 s on a 40 W CO2 and about 9 min 36 s on a 100 W CO2. The layout is 1340 × 790 mm, so most hobby lasers need it split over three or four sheets. Cut the lid and its two rails on the same sheet.
Gift and shop ideas
- A cafe box for stirring spoons, sugar tongs and dessert forks behind the counter
- A wedding gift with initials you engrave on the lid yourself
- A collector's box for vintage teaspoons, one per cell
Questions about this file
What fits in a 6.5 cm cell?
A stack of ten to twelve teaspoons, coffee spoons or cake forks. The narrow cells keep each type standing in its own neat row.
Will full dinner cutlery fit?
Not lying flat, because each row is about 15.5 cm deep. This box is designed for teaspoons and dessert pieces.
How do I keep the lid from sticking?
Rub candle wax on the rails and sand the long lid edges until it slides with light pressure. Lacquer the lid before waxing so it does not swell.
Can I add a picture to the lid?
Yes, place an engrave layer on the lid in your software. The file ships with cut lines only.
Does plywood thickness change the cell size?
3 mm keeps the ten cells as wide as possible. Thicker plywood eats into each cell, so use 4 mm at most unless you want a heavier chest.
Similar files



