VisualizationFive Lane Cutlery Drawer Insert SVG, Wide Silverware Divider Laser Cut File, 36 cm Kitchen Drawer Tray DXF
A free laser cut file for a wide open cutlery drawer insert with five equal lanes running from front to back, 360 × 320 × 70 mm (14.17 × 12.60 × 2.76 in) outside. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood, and its 9 pieces (four walls, a base and four dividers) fit together with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 320 × 70 mm (14.17 × 12.60 × 2.76 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,380 × 476 mm
- Cut length
- 9.20 m
- Est. time, 10 W diode (3 mm)
- 30 min 39 s
- Est. time, 40 W CO2 (3 mm)
- 12 min 46 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF that matches your plywood, cut one divider slot on scrap and check that a divider slides in snugly.
- 02Cut the nine pieces, splitting the 1380 × 476 mm layout across two or three sheets if your bed is smaller.
- 03Set the four dividers into the base, fit the back and both sides around them, then press the front wall on last.
- 04Sand the edges, coat the tray with lacquer or oil, let it dry fully and load one utensil type per lane.
Five long lanes, one per utensil
Four dividers run the full depth of the tray, so every lane is the same: roughly 7 cm wide and 31 cm long inside when cut from 3 mm plywood. That length is the point of this insert. Dinner knives, serving spoons and standard 23 cm chopsticks lie flat without hitting the back wall, which shorter grid trays cannot manage. In the photo the lanes hold, from left to right, dinner forks, tablespoons, dessert spoons, table knives and a bundle of wooden chopsticks.
All walls and dividers are 70 mm tall and the front is straight, so the tray suits a standard kitchen drawer of at least 36 cm inside width. Measure the drawer before cutting: if it is narrower, shorten the base, front, back and dividers in your editor and keep the slot widths as they are.
Cutting and assembly notes
The 3 mm file takes about 30 min 39 s on a 10 W diode, about 12 min 46 s on a 40 W CO2 and about 6 min 08 s on a 100 W CO2. Its layout is 1380 × 476 mm, so most desktop machines will need the pieces spread over two or three sheets; the 360 × 320 mm base is the piece that decides your minimum bed size. A diode laser handles 3 mm in one or two passes, while 5 or 6 mm plywood needs more passes or a CO2 tube.
Stand the four dividers in the base slots first, then add the back and sides and close the box with the front. The joints hold without glue, but a drop of wood glue in each corner stops the tray from racking when the drawer slams.
Finishing and gift ideas
Sand the top edges of the dividers so fingers do not catch, then seal with clear lacquer or hardwax oil so damp spoons do not stain the plywood.
- Sell it with a matching knife block as a kitchen starter set
- Make one per drawer size and list them as a range
- Give it as a housewarming present filled with a new cutlery set
Questions about this file
Will chopsticks and serving spoons fit in the lanes?
Yes. Each lane is about 31 cm long inside, enough for 23 cm chopsticks, dinner knives and most serving spoons lying flat.
My drawer is only 30 cm wide. Can I shrink the tray?
Shorten the long pieces in your editor rather than scaling the whole drawing. Scaling also shrinks the slots, and they must stay as wide as your plywood is thick.
Which thickness works best for a cutlery drawer?
3 or 4 mm birch plywood keeps the lanes wide and the tray light. Use 5 or 6 mm if you want a heavier insert that will not slide around in the drawer.
Could the insert be cut from MDF or acrylic?
Acrylic of the same thickness works and wipes clean easily. MDF cuts well too but swells if water sits on it, so seal it carefully.
What stops the insert shifting when the drawer opens?
Stick small felt or silicone pads under the base corners. They also lift the plywood slightly so drips from wet cutlery can dry.
Similar files



