DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Long light birch plywood tea organizer on a kitchen counter, white tea bags in the low front row and two tins plus yellow and green tea sachets in four back baysVisualization
DW-102005 · UPDATED 11/19/2026

Tea Bag Organizer SVG, Long Sloped Tea Caddy Laser Cut File, Wooden Tea Tin Holder DXF

A long open tea organizer with a full-width front row for loose tea bags and four bays behind it for tins and boxed sachets, with a low front and sloped sides. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in) and is cut as 9 pieces that join with tabs and slots. It has 5 compartments in total.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in)
Parts
9
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,424 × 262 mm
Cut length
6.58 m
Est. time, 10 W diode (3 mm)
21 min 57 s
Est. time, 40 W CO2 (3 mm)
9 min 09 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the SVG or DXF for your plywood thickness and cut one divider first to check that it slides into the step wall without forcing.
  2. 02Cut all 9 pieces, splitting the 1424 mm long layout across two or three sheets if your bed is shorter.
  3. 03Join the base, back and sloped sides, add the 50 mm front, then set the long step wall and push the three back dividers into place.
  4. 04Sand, oil the inside, then line the front row with loose bags and put tins or boxed sachets in the four back bays.

Two rows, two jobs

This caddy splits the counter space into a quick-grab row and a storage row. The front row runs the full 360 mm width behind a 50 mm front wall, so a long line of unwrapped bags can stand on edge where everyone sees them. Behind a lower step wall sit four equal bays, each a little over 11 cm wide, sized for a round tin of loose leaf or a stack of foil sachets. In the photo the back holds two tins and two piles of wrapped bags in yellow and green, while plain white bags fill the front.

The sides slope from the 90 mm back wall down to the front, so even the back bays stay easy to reach on a crowded worktop.

Cutting it out

The 9 pieces are a front, back, two sloped sides, the base, one long step wall and three short dividers for the back row. The flat layout is 1424 × 262 mm, longer than most hobby beds, so split it over two or three sheets: the base and back on one, the sides and dividers on another. Cutting time is about 21 min 57 s on a 10 W diode, about 9 min 09 s on a 40 W CO2 or about 4 min 23 s on a 100 W CO2, all for the 3 mm file. Thicker plywood takes a stronger tube or extra passes on a diode.

Assembly and finish

Fit the base into the back and both sides, then add the low front. Drop the long step wall in next and slide the three dividers into its slots. The joints hold dry; use wood glue if the caddy will be moved a lot. Sand the edges and wipe on a food-safe oil so damp spoons do not mark the wood.

Ideas: fill it with a tea sampler as a housewarming gift, sell it at craft fairs in pairs with a mug rack, or offer it to a small office kitchen.

Questions about this file

How many tea bags fit in the front row?

Standing on edge, roughly 30 to 40 standard paper bags fit along the 360 mm row, depending on how thick the bags are.

Will a tea tin fit in the back bays?

Each back bay is just over 11 cm wide, so round tins up to about 10 cm across fit, and so do upright foil sachets.

Can I make it shorter for a narrow shelf?

Yes, but scale only the length and keep the slot width equal to your plywood thickness, otherwise the tabs will be loose or will not go in.

Does it work in 3 mm MDF or acrylic?

Use the 3 mm file for either. MDF should be sealed in a kitchen, and acrylic edges need a little extra clearance in the slots.

Is there space on the caddy for a name?

The file has cut lines only, but the 50 mm front strip is a good place to add your own engraved word or logo in your laser software.

Similar files