VisualizationEspresso Pod Box SVG, Wooden Coffee Capsule Box With Lid Laser Cut File, Coffee Storage Box DXF
A free laser cut file for an espresso pod box with a separate lift-off lid and three compartments for capsules, tea or coffee sachets and sugar sticks. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood, and the box is 260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in), made from 8 pieces. It goes together with tabs and slots, and the lid is a flat panel that rests on top of the walls.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 160 × 80 mm (10.24 × 6.30 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 860 × 252 mm
- Cut length
- 7.58 m
- Est. time, 10 W diode (3 mm)
- 25 min 16 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 32 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood thickness and cut a corner joint as a test to judge the fit.
- 02Cut the 8 pieces, putting the lid and base on a second sheet if your bed is small.
- 03Press the two dividers into the base, add the long front and back walls, then the two ends, and rest the lid on top to check it sits flat.
- 04Round the lid edges with sandpaper, apply oil, and fill the three compartments before closing it.
Closed storage for the cupboard shelf
Not every coffee stash lives on the counter. This box is meant for a cupboard or pantry shelf, where a lid keeps dust off and lets you stack something on top. The lid is a single 260 × 160 mm panel, the same footprint as the box, and it simply sits on the four walls. Lift it off, lean it behind the box as the photo shows, and everything is in reach.
All four walls are 80 mm tall and the two dividers are 77 mm, just below the rim, so the lid lies flat. The three compartments run side by side. In the photo the left one holds purple and gold espresso capsules, the middle one a row of white tea bags with paper tags, and the right one sugar sticks standing up. Swap in whatever your household drinks: decaf pods, hot chocolate sachets or a handful of stirrers.
Making it
The 3 mm layout is 860 × 252 mm. Cutting time for the 3 mm file is about 25 min 16 s on a 10 W diode, about 10 min 32 s on a 40 W CO2 and about 5 min 03 s on a 100 W CO2. If your bed is around 400 mm, cut the walls on one sheet and the base and lid on another.
Fit the dividers into the base, then the long walls and the short ends. Wood glue at the corners is optional; the lid has no joints at all, so it only needs sanding.
Finishing and gifting
Round the lid edges slightly with sandpaper so it is pleasant to handle. Oil or lacquer brings out the birch grain. The plain lid is a good canvas for an engraved coffee cup, initials or a short message added in your own software. Stocked with a few varieties of pods, it makes a neat gift for a new home or a coffee-loving colleague.
Questions about this file
What keeps the espresso box lid in place?
It is a flat panel that rests on the walls under its own weight. There is no hinge, lip or catch, so it lifts straight off.
Will the lid lie flat over the dividers?
Yes. The dividers are cut 3 mm lower than the walls, so they never touch the underside of the lid.
Will a second pod box stack on top?
The flat lid gives a stable top, so a second box of the same size stacks on it, which is handy on a crowded pantry shelf.
Can I use MDF or acrylic instead of plywood?
Both work. Choose the file closest to the measured thickness of your sheet, and seal MDF if the box will sit near water.
Which thickness should I cut it from?
3 or 4 mm birch gives a light box that a 10 W diode cuts in one or two passes. Thicker sheets look sturdier but need more power or more passes.
Similar files



