VisualizationHinged Silverware Box SVG, Square Flatware Chest With Flip Lid Laser Cut File, Four Section Cutlery Case DXF
A square silverware box with a lid that flips open at the back on pins cut into the plywood, and four equal sections made by two crossing dividers. It measures 300 × 300 × 60 mm (11.81 × 11.81 × 2.36 in), is assembled from 8 plywood pieces with tabs and slots, and is a free SVG and DXF download with separate files for 3, 4, 5 and 6 mm plywood. No metal hinges or screws are needed.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 300 × 60 mm (11.81 × 11.81 × 2.36 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,220 × 376 mm
- Cut length
- 8.39 m
- Est. time, 10 W diode (3 mm)
- 27 min 57 s
- Est. time, 40 W CO2 (3 mm)
- 11 min 39 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the files for your plywood thickness and test the pivot pin in its hole on scrap before the full cut.
- 02Cut the base, front, back, both taller side walls, the two crossing dividers and the lid.
- 03Join base, front and back, place the lid pins into one side wall, add the other side, then slide the two dividers together into a cross.
- 04Open and close the lid a few times, sand any rubbing edge, then oil the box and fill the four sections.
A square box with a 2 by 2 grid
Two full-length dividers cross at the centre and give four sections of the same size, two at the back and two at the front. In the photo the back pair holds forks and spoons, the front pair table knives and dark wooden chopsticks. A 12-piece set for four people fits comfortably, and the square shape means it sits neatly on a sideboard shelf or a tea trolley.
The lid is one 300 × 296.3 mm panel. It turns on round pivot pins at the back of the side walls, which is why the sides are 64.2 mm tall while the back is 60 mm and the front 57 mm. Lift the front edge and the lid swings up and stays resting against the wall behind, as in the photo. Nothing metal is involved, so there is nothing to rust in a kitchen.
Cutting and assembly notes
The 3 mm layout is 1220 × 376 mm. The base and lid are each about 300 mm square, so on a smaller bed cut them on one sheet and the walls and dividers on another. Cutting time for the 3 mm file is about 27 min 57 s on a 10 W diode, about 11 min 39 s on a 40 W CO2 and about 5 min 35 s on a 100 W CO2.
Fit the lid onto its pins while you put the side walls on, because the pins cannot go in once both sides are glued. Check that the lid swings freely, then glue. Sand the back edge of the lid slightly if it rubs on the back wall when it opens.
Ideas for gifts and sets
- A keepsake box for inherited family silver.
- A dessert cutlery box for cake forks and teaspoons.
- Engrave a monogram on the lid and sell it as an anniversary gift.
Questions about this file
How does the lid open without hinges?
Round pins on the lid sit in holes near the back of the side walls and act as the pivot. The whole joint is cut from the same plywood.
Will a full cutlery set for six fit?
Six forks, six spoons and six knives fit in three sections with room to spare, and the fourth section takes teaspoons or chopsticks.
Can I make the box bigger for serving pieces?
Scale the file up, but keep each slot and pin hole at your real plywood thickness, or redraw them after scaling.
Which thickness gives the smoothest lid swing?
4 mm is a good choice: the pins are strong and the lid stays light. Very thin 3 mm pins can snap if the lid is forced.
Can I add a name or a pattern to the lid?
Yes. The file has cut lines only, so add an engraving layer of your own to the lid before you cut it.
Similar files



