DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Birch plywood silverware box with its sliding lid pushed halfway back, showing four sections with table knives, wooden chopsticks, forks and spoons, on a kitchen counter with green cabinets.Visualization
DW-104022 · UPDATED 11/17/2026

Silverware Box With Sliding Lid SVG, Four Compartment Flatware Chest Laser Cut File, Covered Cutlery Storage DXF

A covered silverware box with a sliding lid that runs on two rails and four sections inside, formed by one long divider and one cross divider. It measures 310 × 280 × 70 mm (12.20 × 11.02 × 2.76 in), is made from 10 plywood pieces joined with tabs and slots, and is a free SVG and DXF download with separate files for 3, 4, 5 and 6 mm plywood. The lid has no hinge, and the box has no lock.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
310 × 280 × 70 mm (12.20 × 11.02 × 2.76 in)
Parts
10
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,200 × 646 mm
Cut length
10.14 m
Est. time, 10 W diode (3 mm)
33 min 47 s
Est. time, 40 W CO2 (3 mm)
14 min 05 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the files that match your plywood and test one slot plus a short offcut of lid edge against a rail profile.
  2. 02Cut the base, four walls, both dividers, the two rails and the lid, putting the base and lid on separate sheets on a small bed.
  3. 03Assemble walls and base, cross the two dividers inside, then glue the rails to the side walls with the lid in place and paper spacers.
  4. 04Remove the spacers, wax the lid edges, finish the box with oil or lacquer and sort the cutlery into the four sections.

Four sections under one lid

Two full-length dividers cross in the middle and give four sections. The photo has the lid pushed back halfway: table knives and dark wooden chopsticks sit in the back pair, forks and spoons in the front pair, so the most-used pieces stay reachable even with the lid partly open. Because the lid covers everything, this box works where an open tray does not: on an open shelf, in a sideboard with the good cutlery or packed in a picnic basket.

The front wall is 63.7 mm tall against 70 mm for the back and sides. That small step is the gap the lid slides out through. The two 277 mm rails glue to the inside of the side walls and carry the 303.4 × 279.7 mm lid.

Fitting the lid

The 3 mm layout is 1200 × 646 mm, about twice as tall as an open tray because the base and lid are both close to full size. On a compact laser, put each of those two panels on its own sheet. The time for the 3 mm file is about 33 min 47 s on a 10 W diode, about 14 min 05 s on a 40 W CO2 or about 6 min 45 s on a 100 W CO2.

Glue the rails while the lid is already in place, with a strip of paper on each side as a spacer. Once the glue sets, pull the paper out and the lid will run with a little play instead of jamming.

Gift ideas

  • Engrave the lid with a family name and give it with a new cutlery set as a wedding present.
  • Sell it as a chopstick and sushi set box with lacquered chopsticks inside.
  • Keep one as a travel cutlery case for the camper or the cabin.

Questions about this file

Why is the front wall lower than the others?

The lid slides out over it. The front is 63.7 mm tall while the other walls are 70 mm, which leaves room for the lid to pass.

Can the lid lock or stay shut when carried?

There is no lock, so carry the box level. A rubber band or a cord wrapped around it keeps the lid closed on a picnic.

Are the four sections equal?

One long divider and one cross divider meet near the centre, so the four sections are close in size. Each is roughly 150 mm wide and 135 mm deep inside.

Which thickness should I cut for a smooth lid?

3 or 4 mm gives the lightest lid and the easiest slide. A 6 mm lid is sturdy but heavier, so wax the rails well.

Can I engrave a picture on the lid?

The file holds cut lines only, but you can add your own engraving layer to the lid before cutting. Keep the design away from the edges that run in the rails.

Similar files