VisualizationSloped Napkin Organizer SVG, Napkin Holder with Straw Cells Laser Cut File, Five Section Kitchen Caddy DXF
A free open napkin organizer with five compartments: one full-depth section for upright napkins and a two-by-two grid beside it for straws, coasters and toothpicks, with a 70 mm front wall and sides sloping up to the 100 mm back. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the organizer measures 260 × 220 × 100 mm (10.24 × 8.66 × 3.94 in) and is made from 9 pieces joined with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 220 × 100 mm (10.24 × 8.66 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 332 mm
- Cut length
- 6.19 m
- Est. time, 10 W diode (3 mm)
- 20 min 37 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 35 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood thickness and test the cross divider slot on a scrap strip.
- 02Cut the 9 pieces, in two runs if the 980 mm layout is longer than your bed.
- 03Fit back, front and sloped sides to the base, add the long divider, then the cross divider and the two short dividers of the grid.
- 04Sand, seal, and fill the napkin section and the four grid cells.
The layout
A tall divider from front to back cuts the box into a napkin section on the left and a working area on the right. A cross divider splits that right part into a back row and a front row, and two short dividers make two cells in each row, so the right half becomes a neat two-by-two grid. The back cells rise to the full 100 mm, ideal for straws, while the front cells are lower to follow the slope of the sides. In the photo the napkin section holds a thick stack of white napkins standing upright, the back cells carry steel straws, glass straws and bamboo straws, and the front cells hold cork coasters and a glass of toothpicks.
Cutting it
The 3 mm layout is 980 × 332 mm; split it over two runs if your bed is around 400 to 500 mm. The estimated time for the 3 mm file is about 20 min 37 s on a 10 W diode, about 8 min 35 s on a 40 W CO2 and about 4 min 07 s on a 100 W CO2. A 10 W diode needs one or two passes for 3 mm and several for the 5 or 6 mm versions.
Putting it together and using it
Build the outer walls on the base first, set the long divider, then the cross divider, and finish with the two short dividers. The parts lock without glue, but a little wood glue at the base corners stiffens it for a busy counter. Sand and seal it with lacquer or food-safe oil. It suits a coffee bar, a cafe table or a kids' party table, and a set of two with a logo or family name engraved on the front makes a thoughtful housewarming present.
Questions about this file
What goes in the four small cells?
The two back cells are tall enough for straws or stir sticks, and the two lower front cells suit coasters, sugar packets or a toothpick glass.
Do napkins stand upright?
Yes. The napkin section runs the full 220 mm depth, so a stack of folded paper napkins stands on edge and leans gently against the back.
Can I scale it?
Scaling works if you correct the slot widths to your sheet thickness afterwards, as the grid joints depend on an exact fit.
Is the sloped front sturdy enough?
The 70 mm front wall is locked into the base and both sides, so it stays firm. Use the 4 mm file for extra stiffness on a busy counter.
How do I keep it clean at a coffee bar?
Seal it with two coats of clear lacquer so spilled sugar and coffee drips wipe off without staining the plywood.
Similar files



