DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Long light birch plywood box with its lid leaning beside it, holding paper napkins, cork coasters, toothpicks and metal straws in compartments on a kitchen counterVisualization
DW-105045 · UPDATED 11/21/2026

Table Setting Box with Lid SVG, Eight Compartment Napkin Chest Laser Cut File, Long Lift Off Lid Box DXF

A free long, narrow table setting box with eight cells in two rows of four and a separate lid that lifts off, for napkins, coasters, toothpicks and straws. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 380 × 160 × 90 mm (14.96 × 6.30 × 3.54 in) and is made from 10 pieces that join with tabs and slots, with dividers that slot together.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
380 × 160 × 90 mm (14.96 × 6.30 × 3.54 in)
Parts
10
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,484 × 332 mm
Cut length
11.77 m
Est. time, 10 W diode (3 mm)
39 min 13 s
Est. time, 40 W CO2 (3 mm)
16 min 21 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the file for your plywood and check one wall tab against a lid slot cut from scrap.
  2. 02Cut the 10 pieces in runs that suit your bed: base and lid, walls, then the four dividers.
  3. 03Build the walls on the base, lay in the long divider, slot the three short dividers across it, then try the lid.
  4. 04Sand, finish with oil or lacquer, and sort napkins, coasters, picks and straws into the eight cells.

Long and slim

At 380 mm long but only 160 mm deep, this box fits on a narrow shelf, a sideboard or down the middle of a dining table without taking over. Inside, three short dividers cross one long divider to make two rows of four cells, roughly 90 × 75 mm each when cut from 3 mm plywood. The dividers stop at about 79 mm, a little below the 90 mm walls, so contents can poke up slightly and the lid still closes.

The lift-off lid

The flat lid is a separate piece with four slots that drop over small tabs on top of the walls, which keeps it sitting square instead of sliding around. Lift it off and lean it against the wall while the table is in use, as in the photo, where napkins, cork coasters, a glass of toothpicks and metal straws fill the back row and a run of folded white napkins sits along the front.

Cutting, finishing and gift ideas

The 3 mm layout is 1484 × 332 mm, so cut it in two or three runs on a hobby laser: base and lid together, then the walls, then the dividers. The estimated time for the 3 mm file is about 39 min 13 s on a 10 W diode, about 16 min 21 s on a 40 W CO2 and about 7 min 51 s on a 100 W CO2. The 5 and 6 mm versions need a stronger laser or extra passes. Sand the lid edges, then seal everything with oil or clear lacquer. Ideas: a picnic or camping box packed with napkins and cutlery, a holiday table gift with an engraved lid, or a set of three in different stains for a craft fair table.

Questions about this file

How big is each cell?

With 3 mm plywood each of the eight cells is about 90 mm wide and 75 mm deep, a little smaller with thicker sheets. Paper cocktail napkins and round coasters fit flat.

Why are the dividers lower than the walls?

They stop at about 79 mm so items can sit slightly proud of the dividers while the lid still closes flat on the walls.

Can I take some dividers out?

Yes. Leave out one short divider to make a double cell for long items such as wrapped cutlery; the rest of the grid still holds together.

Will the lid fall off when carried?

It rests on the walls and is held square by its slots, but it is not locked, so carry the box level or with a hand on the lid.

Can I engrave the lid?

Yes. The file has cut lines only, so add a name, date or pattern in your laser software and engrave it before cutting the lid.

Similar files