DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood three-tier stand with nine bins holding white paper napkins, cork coasters and woven coasters, with metal straws and toothpicks beside it on a kitchen counterVisualization
DW-105070 · UPDATED 11/21/2026

Napkin and Coaster Stand SVG, Three Step Buffet Riser Laser Cut File, Tiered Cafe Counter Display DXF

A free three-tier stand with three bins on each step, nine in all, for paper napkins and cork or woven coasters on a buffet, cafe counter or kitchen island. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the stand measures 380 × 240 × 180 mm (14.96 × 9.45 × 7.09 in), is made of 15 tab-and-slot pieces with small engraved part numbers, and each higher step sits further back so every bin stays in view.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
380 × 240 × 180 mm (14.96 × 9.45 × 7.09 in)
Parts
15
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,540 × 328 mm
Cut length
11.87 m
Est. time, 10 W diode (3 mm)
39 min 34 s
Est. time, 40 W CO2 (3 mm)
16 min 29 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file for your plywood, then cut a single shelf slot and one divider on scrap to confirm they slide together.
  2. 02Cut the 15 pieces in two or three runs and keep them grouped by their engraved numbers.
  3. 03Build on one side panel: front board, step boards, shelves and brace first, then the second side, then all six dividers.
  4. 04Sand the step edges, seal with clear lacquer, and fill the nine bins with napkins and coasters.

Three steps, nine bins

Each step is a shelf with a low board in front of it, and two short dividers on every shelf turn it into three bins. The bottom shelf is the deepest at 97 mm, the two upper shelves are about 89 mm, and the top row sits back and up where guests can still reach it over the lower rows. In the photo the left bin of each step holds white paper napkins, the middle one cork coasters and the right one woven rattan coasters. The straw cup and toothpick glass beside it stand on their own and are not part of the file.

Cutting and assembly

The 3 mm layout is 1540 × 328 mm, so most people cut it in two or three runs. The estimated time for the 3 mm file is about 39 min 34 s on a 10 W diode, about 16 min 29 s on a 40 W CO2 and about 7 min 55 s on a 100 W CO2. Every piece carries a small engraved part number, which makes the 15 parts quick to sort. Lay one stepped side flat, plug in the front board, the two step boards, the three shelves and the rear brace, then cap the frame with the second side. The six dividers drop into their shelf slots last. For 5 and 6 mm plywood a diode needs several passes, or use a CO2 laser.

Where it works

A tiered stand earns its space wherever people serve themselves: a coffee shop pickup counter, a hotel breakfast buffet, a wedding drinks table or a busy family kitchen. Stain it to match the counter, engrave a cafe logo on the front board, and finish it with clear lacquer so sticky fingers wipe off. Two stands side by side make a full self-service station for a market stall or event.

Questions about this file

What fits in each bin?

Each step is split into three bins across the 380 mm width, roughly 120 mm each, which suits folded paper napkins, round 4 inch coasters or sugar packets.

What are the little numbers on each piece for?

Small part numbers are engraved so you can tell the similar shelves and step boards apart while you build. Apart from those numbers, nothing else is engraved.

Can I shrink it for a narrow counter?

Scaling is possible, but every slot must then be set back to your plywood thickness, otherwise the shelves will not seat in the sides.

Does the stand need glue?

The frame locks together firmly on tabs and slots. Glue the side joints only if the stand will be carried around full between events.

Is there room for a coffee shop logo?

Yes. Place the logo on the front board in your laser software and engrave it before the outline is cut.

Similar files