DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Long light birch plywood book box with its cover open, leaf-print napkins, cork coasters, toothpicks and gold forks arranged inside, on a marble kitchen counterVisualization
DW-105055 · UPDATED 11/21/2026

Book Box SVG, Living Hinge Napkin Box Laser Cut File, Flex Spine Wooden Storage Box DXF, Long Book Style Box

A free book-style box whose one-piece cover wraps over the top and bends on a living-hinge spine of thin kerf cuts, with one long open compartment inside for napkins, coasters and table extras. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 400 × 180 × 90 mm (15.75 × 7.09 × 3.54 in) and is made from 7 pieces joined with tabs and slots, including a small pin that keeps the cover closed.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
400 × 180 × 90 mm (15.75 × 7.09 × 3.54 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
2,055 × 188 mm
Cut length
16.99 m
Est. time, 10 W diode (3 mm)
56 min 39 s
Est. time, 40 W CO2 (3 mm)
23 min 36 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the 3 or 4 mm file for the easiest bend and test-cut a short strip of hinge pattern to see how it flexes in your sheet.
  2. 02Cut the 7 pieces on a bed long enough for the 847 mm cover.
  3. 03Join the front and back to the two side panels, then roll the cover around the rounded ends, seating its tabs as you go.
  4. 04Fit the small pin through the front tab, oil the box lightly and fill it with napkins or table extras.

How the book cover works

One long cover piece forms the base, the curved spine and the top of the box. Rows of short kerf cuts in the spine section let the plywood bend around the rounded ends of the two long side panels, just like the spine of a hardback. The flex spine bends best in good-quality birch plywood without voids; cheap plywood with gaps in the core tends to crack at the cuts. A small pin slides through a tab on the front panel to keep the cover shut.

Inside the box

The file gives one long, open compartment, 400 mm from end to end. In the photo the inside is arranged into four zones holding leaf-print napkins, cork coasters, a glass of toothpicks and gold forks, which shows how the space can be used; if you want fixed sections, glue in strips of offcut plywood after assembly. Closed, it looks like a large wooden book on a shelf, which makes it a nice place to keep party napkins or a set of place cards between dinners.

Cutting notes

The cover piece is about 847 mm long, so this box needs a laser bed of at least roughly 850 × 180 mm; it cannot be split like the smaller boxes. The 3 mm layout is 2055 × 188 mm in total. The many hinge cuts make it the slowest box in this set: the estimated time for the 3 mm file is about 56 min 39 s on a 10 W diode, about 23 min 36 s on a 40 W CO2 and about 11 min 20 s on a 100 W CO2. The 3 and 4 mm versions flex most easily. Finish with a thin oil rather than thick lacquer so the spine keeps bending, and offer it as a wedding guest book box or a gift for a keen host.

Questions about this file

What size laser do I need?

The one-piece cover is about 847 × 180 mm, so the work area must be at least that long. Most small diode lasers are too short for it.

Which plywood works best for the flex spine?

Good birch plywood with a solid core bends cleanly. Poplar or plywood with voids can snap along the kerf cuts.

Can I make the hinge stiffer or softer?

Thinner sheet gives a softer bend; the 3 mm version is the most flexible and the 6 mm version the stiffest. Do not scale the hinge area, as the cut spacing is tuned to the file.

Does the box have dividers?

No, it is one long open compartment. Glue in strips of offcut if you want separate spaces like those in the photo.

How should I finish it?

Use a thin oil or wax. A heavy lacquer fills the kerf cuts and makes the spine crack when it bends.

Similar files