VisualizationNapkin Caddy SVG, Sloped Table Organizer Laser Cut File, Wooden Napkin and Coaster Holder DXF
This is a free laser cut napkin caddy with a sloped front: a wide napkin section on the left and three small pockets lined up front to back on the right, four compartments in all. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 240 × 200 × 100 mm (9.45 × 7.87 × 3.94 in) and is made from 8 pieces that join with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 200 × 100 mm (9.45 × 7.87 × 3.94 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 900 × 312 mm
- Cut length
- 5.21 m
- Est. time, 10 W diode (3 mm)
- 17 min 22 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 14 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF that matches your plywood thickness and cut one slot and tab first to check the fit.
- 02Cut all 8 pieces: front, back, two sloped sides, base, the long divider and the two short cross dividers.
- 03Set the sides and back into the base, add the low front, then slide in the long divider and drop the two cross dividers into its slots.
- 04Sand, oil or lacquer the caddy, then load napkins on the left and straws, toothpicks and coasters on the right.
What fits inside
The left half is one deep slot for folded paper napkins standing on edge, so guests pull one off the front of the stack. On the right a long divider runs from front to back, and two short cross dividers split that strip into three pockets. In the photo the back pocket holds metal straws, the middle one a small jar of toothpicks and the front one a stack of cork coasters. The front wall is 60 mm tall against a 100 mm back, and the side panels slope down between them, so the napkins and the front pocket stay easy to reach from the table. The two cross dividers are cut at different heights to follow that slope.
Cutting and fitting the layout
The 3 mm layout is 900 × 312 mm. On a smaller bed, move the base and the back to a second sheet and keep the sides, front and dividers together. Cutting time for the 3 mm file is about 17 min 22 s on a 10 W diode, about 7 min 14 s on a 40 W CO2 and about 3 min 28 s on a 100 W CO2. A diode handles 3 mm in one or two passes; 5 and 6 mm boards need several passes or a CO2 tube. The file holds cut lines only.
Finishing and gift ideas
Sand the tab ends lightly before you press them home. The joints hold without glue, but a little wood glue in the base slots makes the caddy rigid for daily use on a dining table. Wipe on hard-wax oil or clear lacquer so spilled drinks and sauce rinse off. Fill one with patterned napkins, bamboo straws and coasters as a housewarming gift, sell them in pairs for cafe tables, or make a version in walnut plywood for a holiday table set.
Questions about this file
What size napkins fit the wide slot?
Folded cocktail and lunch napkins stand on edge in the left section. Measure your napkins against the 240 mm length before cutting, since the right-hand pockets take part of it.
Can I make the caddy larger for dinner napkins?
Yes, scale the drawing in your laser software, but restore every slot width to your real board thickness afterwards or the tabs will be loose or will not go in.
Will 3 mm MDF or acrylic work?
Both cut cleanly with the 3 mm file. Acrylic needs a CO2 laser and a solvent cement instead of wood glue, and MDF should be sealed if the caddy stays near a sink.
Why are the two short dividers different heights?
They sit under the sloped sides, so the back one is taller than the front one. Keep them in the right order when you assemble the right-hand strip.
Can I add a restaurant or family name?
Add a text layer on the front panel in your laser software and engrave it before the cut pass; the file itself does not include any lettering.
Similar files



