VisualizationHinged Coffee Box SVG, Coffee Capsule Chest Laser Cut File, Wooden Coffee Gift Box With Lid DXF
A free laser cut file for a coffee chest with a flip-up lid and three compartments for capsules, drip coffee bags and sugar sticks. It is supplied as SVG and DXF for 3, 4, 5 and 6 mm plywood, measures 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in) and has 8 pieces. The lid pivots open at the back on pins cut into the plywood, and the box assembles with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 180 × 80 mm (9.45 × 7.09 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 860 × 276 mm
- Cut length
- 6.26 m
- Est. time, 10 W diode (3 mm)
- 20 min 53 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 42 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood and cut one pin and its hole first to make sure the lid will turn freely.
- 02Cut the 8 parts, splitting the 860 mm layout over two sheets on a small bed.
- 03Fit the dividers into the base, add the front, back and first side, set the lid pins in place, then close it in with the second side.
- 04Sand the pivot edge until the lid swings smoothly, finish with oil, and fill the three compartments.
A lid that stays with the box
With a lift-off lid there is always the question of where to put it down. Here the lid pivots at the back on pins that are part of the plywood, so it swings up, rests open and swings back down. Nothing to buy and nothing to screw in. The two side panels are 84 mm tall, a little taller than the 80 mm front and back, because they carry the pivot points.
Inside, two full-depth dividers make three compartments across the 240 mm length. In the photo the left one holds a mix of gold and purple espresso capsules lying on their sides, the middle is packed with paper drip coffee bags, and the right compartment keeps brown sugar sticks on end. At 180 mm deep it has room for sachets standing upright.
Cutting and fitting the lid
The 3 mm sheet is 860 × 276 mm. On a smaller bed, cut the lid and base on one sheet and the walls on another. The 3 mm file cuts in about 20 min 53 s on a 10 W diode, about 8 min 42 s on a 40 W CO2 or about 4 min 11 s on a 100 W CO2.
Build the box first: dividers into the base, then front, back and one side. Hook the lid's pins into that side panel before adding the second one, because the pins cannot go in once both sides are fixed. Open and close it a few times before gluing anything, and sand the back edge of the lid if it rubs.
As a gift
A chest with a lid feels like a present even when it is empty. Fill it with a selection of capsules or single-origin drip bags, tie a ribbon round it, and it suits a teacher, a colleague or a new neighbour. Add your own engraving on the lid, which is the largest flat face of the box.
Questions about this file
How does the lid open?
It turns on pins cut into the plywood at the back of the box. Everything is wood, and the lid stays attached while it is open.
What can I keep in the three compartments?
Espresso capsules, drip coffee bags and sugar sticks, as in the photo, or tea bags and stirrers. Each compartment runs the full 180 mm depth.
Can I make the chest from 6 mm plywood?
Yes, the download includes a 6 mm version. It gives a heavier, sturdier chest, but a 10 W diode needs several passes, so a CO2 laser is easier.
Can it be scaled up for a bigger capsule collection?
You can enlarge the outline, but the slots and pivot holes must match your material thickness. Correct them after scaling or the lid and joints will not fit.
How do I protect it from coffee spills?
A coat of hardwax oil or clear lacquer inside and out lets you wipe drips away. Keep the chest clear of the steam outlet on the machine.
Similar files



