DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood caddy with sloped sides and five upright slots holding two olive oil pourers, balsamic vinegar, a light oil, chili sauce and pesto on a white marble kitchen counterVisualization
DW-106010 · UPDATED 11/19/2026

Oil Bottle Caddy SVG, Sloped Condiment Holder Laser Cut File, Olive Oil Dispenser Organizer DXF

This is an open caddy for oil dispensers, vinegar and sauce bottles, with five sections side by side, a front wall lower than the back and side panels that slope down to it. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood and builds a 360 × 200 × 80 mm (14.17 × 7.87 × 3.15 in) caddy from 9 pieces joined with tabs and slots.

Author
DXF World · 368 files
Formats
SVG, DXF
Outer size (W × D × H)
360 × 200 × 80 mm (14.17 × 7.87 × 3.15 in)
Parts
9
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,184 × 292 mm
Cut length
7.02 m
Est. time, 10 W diode (3 mm)
23 min 24 s
Est. time, 40 W CO2 (3 mm)
9 min 45 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the file for the plywood you have, then cut a single slot from an offcut and push a tab into it to confirm the fit.
  2. 02Cut the base, back, low front, two sloped sides and four dividers, rearranging them over two sheets on a smaller bed.
  3. 03Slot the back and sides into the base, close the front, and push the four dividers in from left to right so each sits flat on the base.
  4. 04Sand, seal against oil drips, and stand the pourers and sauce bottles upright in the five slots.

What goes in the five slots

Four dividers run from front to back and split the 360 mm length into five upright bays. The back wall is 80 mm tall and the front only 56 mm, so the sides angle down and you can grab a bottle by the neck without lifting it over a high rim. In the photo two olive oil pourers with steel spouts stand at the left, followed by balsamic vinegar, a light oil, chili sauce and a jar of pesto. It is a good fit for the counter next to the stove, where cooking oils get reached for every day.

Laser and material notes

The nine pieces lie on a 1184 × 292 mm layout. On a typical diode bed of around 400 mm you will need to split it: the base and back first, then the front, sides and four dividers. Cutting takes about 23 min 24 s on a 10 W diode, about 9 min 45 s on a 40 W CO2 and about 4 min 41 s on a 100 W CO2, all for the 3 mm file. At 3 mm a 10 W diode needs one or two passes; 5 and 6 mm sheets call for more passes or a CO2 machine.

Sealing and selling

Oil bottles always leave a ring, so seal the base well with two coats of clear lacquer or a hard wax oil after sanding the edges. Glue is optional: the slots hold the dividers firmly, but a few drops of wood glue keep the caddy square for years. Selling ideas: bundle it with a pair of glass oil dispensers, offer it in a dark stain for modern kitchens, or make it a wedding gift with the couple's initials engraved on the front.

Questions about this file

Will oil dispensers with pour spouts fit?

Yes, the photo shows two standard glass pourers sharing the first bay. Bottles stand upright and rise well above the 80 mm back wall.

Why does the front sit lower than the back?

The 56 mm front and sloped sides make it easier to see labels and pull a bottle out without tipping the others.

Can the caddy be made bigger for large bottles?

Enlarging works only if every slot stays as wide as your sheet thickness. Scale the drawing, then reset the slot widths to the material before cutting.

Will 3 mm plywood carry five full glass bottles?

For small bottles 3 mm is fine, but 4 or 5 mm gives a stiffer base under heavy oil dispensers.

Can it stand next to the sink?

Only if every surface is sealed. Use a waterproof lacquer, let it cure fully and wipe off splashes rather than leaving it wet.

Similar files