DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood coffee tray with three compartments holding gold and rose espresso capsules, drip coffee sachets and sugar sticks, on a marble counter next to a coffee machine and pink hydrangeas.Visualization
DW-103001 · UPDATED 11/17/2026

Coffee Pod Holder SVG, Sloped Capsule Tray Laser Cut File, Wooden Coffee Station Organizer DXF

A free laser cut file for a small open coffee tray with three side-by-side sections for pods, drip coffee bags and sugar sticks. It comes as SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood and measures 240 × 160 × 80 mm (9.45 × 6.30 × 3.15 in). The 7 pieces join with tabs and slots, and the front wall is lower so the sides slope down toward you.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
240 × 160 × 80 mm (9.45 × 6.30 × 3.15 in)
Parts
7
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
820 × 252 mm
Cut length
4.38 m
Est. time, 10 W diode (3 mm)
14 min 35 s
Est. time, 40 W CO2 (3 mm)
6 min 05 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Open the folder for your plywood thickness and cut one divider slot as a test before running the whole 820 mm layout.
  2. 02Cut the 7 parts, moving the base or a side panel to a second sheet if your bed is too short.
  3. 03Push the two dividers into the base, fit the tall back and the two angled sides, and close it with the low front.
  4. 04Ease the edges with sandpaper, oil the tray, and load pods on the left, sachets in the middle and sugar sticks on the right.

Three lanes beside the machine

This is the smallest open tray in the coffee set: 240 mm long, roughly the width of a single-serve machine, so it can sit right next to the brewer without taking over the counter. Two dividers run front to back and split it into three equal lanes. In the photo the left lane holds a loose pile of capsules in gold, rose and bronze, the middle one carries a stack of drip coffee sachets standing on edge, and the right one keeps paper sugar sticks upright.

The back wall is 80 mm tall while the front is only 48 mm, and the side panels are cut at an angle between the two. That lower lip lets you grab a pod from the bottom of the pile without lifting the tray, and the sachet fronts stay visible so you can pick a roast at a glance.

Cutting and putting it together

The 3 mm layout is 820 × 252 mm. Many diode beds are shorter than that, so move the base and one side onto a second sheet. On a 10 W diode the 3 mm file takes about 14 min 35 s, while a 40 W CO2 needs about 6 min 05 s and a 100 W CO2 about 2 min 55 s. With 5 or 6 mm stock a diode laser will need slower speed or extra passes.

Slot both dividers into the base, then add the back wall, the angled sides and the short front last. Friction holds it well; a thin bead of wood glue in the corners keeps it square through years of daily use.

Small gifts and coffee corners

Sand the edges, then wipe on a hardwax oil so drips of coffee come straight off. Fill it with a sampler of pods and a few sachets for a coffee lover's birthday, or make three in a row for an office kitchen. Craft fair sellers can sell it flat-packed in a sleeve and let buyers assemble it at home.

Questions about this file

How many coffee pods fit in one lane?

Each lane is about a third of the 240 mm length, so a loose heap of a dozen or more small espresso capsules fits, as in the photo. Larger pods for other machines fit too, just fewer of them.

Will drip coffee bags stand up inside?

Yes. The tray is 160 mm deep and the dividers run the full depth, so standard drip sachets stand on edge and lean against the back wall.

Can I make this pod tray bigger?

Scaling the drawing stretches the slots too, so they no longer match your sheet. Resize the outline, then set every slot back to the exact thickness of your plywood.

Which thickness suits such a small tray?

3 or 4 mm birch keeps it light and cuts quickly on a diode. Choose 5 or 6 mm only if you want a chunkier look and your laser cuts it cleanly.

Can I add a logo or name to the front?

There is nothing to engrave in the download, only cut lines. Add your own engraving to the 48 mm front, which faces you on the counter, or to one of the side panels before you send the job.

Similar files