DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Long light birch plywood spice organizer with four back compartments holding small glass jars with silver lids and a low front tray of seasoning sachets, on a stone kitchen counter by a window.Visualization
DW-101005 · UPDATED 11/17/2026

Spice Jar Organizer SVG, Spice Packet Tray Laser Cut File, Long Wooden Seasoning Caddy DXF

A free laser cut file for a long open spice organizer with a low front tray for seasoning sachets and four jar compartments behind it, five sections in all. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in), has a lowered front with sloped sides and is made of 9 pieces that fit together with tabs and slots.

Author
DXF World · 335 files
Formats
SVG, DXF
Outer size (W × D × H)
360 × 160 × 90 mm (14.17 × 6.30 × 3.54 in)
Parts
9
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,424 × 262 mm
Cut length
6.46 m
Est. time, 10 W diode (3 mm)
21 min 33 s
Est. time, 40 W CO2 (3 mm)
8 min 59 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Pick the SVG or DXF that matches your plywood and cut one jar divider from scrap to check the slot fit.
  2. 02Cut all nine pieces, moving the 360 mm base and back to their own sheet if the layout is too long for your bed.
  3. 03Join the back, both sloped sides and the low front around the base, then drop in the long cross divider and the three jar dividers.
  4. 04Sand the slope edges, apply oil or lacquer, and load jars at the back and seasoning sachets in the front tray.

Two kinds of storage in one box

Most kitchens keep both jars and flat seasoning packets, and they rarely fit the same space. This organizer splits the 360 mm length into two zones. Along the back, three short dividers make four bays of roughly 88 mm each, which take three small round jars side by side. In front of them a single long tray runs the whole width, fenced by a 54.5 mm cross divider, and that is where the packets stand on edge like index cards.

The front wall is only 36 mm tall, 40% of the 90 mm back, and the side panels slope down to it. You can read every packet without lifting it, and the jar lids stay easy to grab over the low lip.

Cutting notes

The nine pieces are a front, a back, two sloped sides, the base, the long cross divider and three jar dividers. The 3 mm layout is 1424 × 262 mm, so on a typical diode or desktop CO2 bed you will split it across two or three sheets; the base and back are the longest parts at 360 mm. For the 3 mm file, expect about 21 min 33 s on a 10 W diode, about 8 min 59 s on a 40 W CO2 and about 4 min 19 s on a 100 W CO2. A 10 W diode handles 3 mm in one or two passes, while 5–6 mm needs several passes or a stronger tube.

Tabs and slots hold without glue. Add a little wood glue in the corners if the organizer will be moved around full of glass jars. Sand the sloped edges and wipe on oil or clear lacquer so spilled paprika comes off easily.

Gift and shop ideas

Fill the four bays with house blends and the tray with recipe cards for a housewarming gift. Etsy sellers can offer it bare or with a dozen matching jars.

Questions about this file

What goes in the low front tray?

Flat seasoning sachets, gravy mix packets or folded recipe cards. The tray runs the full width, so packets of different sizes can stand in one row.

How many jars fit in the back row?

Each of the four bays is about 88 mm wide, which takes three slim spice jars about 45 mm across, so twelve small jars in all.

Can I cut this organizer from 3 mm MDF instead of plywood?

Yes, MDF of the same thickness works with the same file. Seal it well, because raw MDF swells if it gets wet near the sink.

Can I make it shorter to fit a narrow shelf?

Scaling the whole drawing changes the slot widths too, so the tabs stop fitting. Shorten it in a vector editor and keep every slot equal to your sheet thickness.

Is there room to engrave a family name on the low front wall?

The 36 mm front is narrow, so a short word or small logo fits best. Add it as an engrave layer before cutting; the file itself contains only cut lines.

Similar files