DXF / SVG / GeneratorsFiles. Tools. Possibilities.
EN
Saved0
Light birch plywood box with a sliding lid pushed back, showing white embossed napkins in a wide section and toothpicks, metal straws and cork coasters in a side section on a kitchen counterVisualization
DW-105027 · UPDATED 11/21/2026

Napkin Box with Sliding Lid SVG, Covered Napkin Storage Laser Cut File, Kitchen Counter Napkin Box DXF

A free covered napkin box with a sliding lid and two sections: a wide one for a stack of paper napkins and a narrower one beside it for straws, toothpicks or coasters. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 310 × 200 × 80 mm (12.20 × 7.87 × 3.15 in), is made from 9 pieces with tabs and slots, and the lid slides in on two rails.

Author
DXF World · 530 files
Formats
SVG, DXF
Outer size (W × D × H)
310 × 200 × 80 mm (12.20 × 7.87 × 3.15 in)
Parts
9
Material thickness
3, 4, 5 or 6 mm plywood (a file for each)
Layout size (3 mm file)
1,225 × 292 mm
Cut length
7.67 m
Est. time, 10 W diode (3 mm)
25 min 34 s
Est. time, 40 W CO2 (3 mm)
10 min 39 s
Layers
CUT only, no engraving

Free account required to download

How to make it

  1. 01Choose the file that matches your plywood and test-cut one rail and a short strip of lid to check the sliding fit.
  2. 02Cut all 9 pieces, base and lid in the first run if your bed is small.
  3. 03Assemble base, back and sides, glue the two rails inside the side walls, add the divider, then the lower front.
  4. 04Sand and wax the lid edges, finish the box with oil or lacquer, and fill it with napkins and table extras.

Why a lid helps

An open caddy collects dust and crumbs, while this box keeps napkins clean between meals. The lid runs on two thin rails fixed inside the side walls and slides out over the slightly lower front wall, so there is no hinge to wear out. Pull it halfway to reach the napkins, or take it off completely while the table is set. One divider running front to back makes the two sections. In the photo the lid is pushed back to show embossed white napkins lying flat in the big section, with a glass of toothpicks, metal straws and cork coasters packed into the side section.

Cutting details

The pieces fit a 1225 × 292 mm layout for 3 mm plywood; on a smaller bed, cut the base and lid first and the walls, rails and divider in a second run. The estimated time for the 3 mm file is about 25 min 34 s on a 10 W diode, about 10 min 39 s on a 40 W CO2 or about 5 min 07 s on a 100 W CO2. Sheets of 5 or 6 mm want a CO2 laser or several diode passes. Before gluing anything, test the lid in its rails: it should slide under light pressure.

Assembly and finishing

Fit the back and both sides to the base, glue the two rails along the inside of the side walls, set the divider and close the box with the front. If the lid binds, sand its edges a little and rub them with wax so it glides. Oil or clear lacquer keeps it clean on a kitchen counter. Ideas: a lidded napkin box for a camper van or patio table, a gift paired with a set of cloth napkins, or a bakery counter box with the shop logo engraved on the lid.

Questions about this file

What holds the sliding lid in place?

It rests on two rails glued inside the side walls and slides between them. There is no lock, so keep the box upright when carrying it.

Will lunch napkins fit?

Folded lunch-size paper napkins lie flat in the wide section, as in the photo. The inside depth is a little under 200 mm.

Which thickness slides best?

All four files work. A 3 or 4 mm lid is light and glides easily, while a 6 mm lid feels solid but needs well-sanded edges.

Is it possible to personalise the lid?

Yes. The file has cut lines only, so add a name, monogram or logo to the lid in your laser software and engrave it before cutting.

Can I use MDF instead of plywood?

Yes, 3 or 4 mm MDF cuts cleanly and paints well. Seal it, because raw MDF swells near a sink or kettle.

Similar files