VisualizationCutlery Box With Lid SVG, Wooden Silverware Storage Laser Cut File, Flatware Box DXF, Utensil Chest
A free SVG and DXF file for a wooden cutlery box with four compartments and a separate flat lid that lifts off. Outer size is 320 × 280 × 60 mm (12.60 × 11.02 × 2.36 in); the 8 plywood pieces assemble with tabs and slots, and there are separate files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 280 × 60 mm (12.60 × 11.02 × 2.36 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,248 × 352 mm
- Cut length
- 10.20 m
- Est. time, 10 W diode (3 mm)
- 34 min 00 s
- Est. time, 40 W CO2 (3 mm)
- 14 min 10 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the SVG or DXF for the plywood you have and cut a short test piece to make sure the tabs press in by hand.
- 02Cut the lid and base on the first pass and the four walls with the two dividers on the next, or all together on a wide bed.
- 03Seat the front, back and side walls on the base, cross the two dividers inside and lay the lid on top to confirm it sits flat.
- 04Sand, oil both faces of the lid so it does not warp, and sort the cutlery into the four compartments.
Box, dividers and lid
The box has four even walls of 60 mm and a crossed pair of dividers that split it into four bays. The dividers are cut 3 mm lower than the walls, so the lid rests flat on the rim instead of on the cross. The lid is a single panel the same size as the footprint; you lift it off and set it aside, or lean it against the back as in the photo. There, the back bays hold dinner forks and spoons and the front bays hold table knives and a row of chopsticks. Keeping the lid on means fewer dust and crumbs on cutlery stored in an open cupboard or on a shelf.
Laser settings and layout
The layout is 1248 × 352 mm, so on a smaller bed cut the lid and base first and the walls and dividers afterwards. The 3 mm file needs about 34 min 00 s with a 10 W diode, about 14 min 10 s on a 40 W CO2 and about 6 min 48 s on a 100 W CO2. Most of that time goes into the two large panels. A 10 W diode cuts 3 mm in one or two passes; thicker sheets call for a more powerful machine or extra passes. Build the walls around the base, drop in the crossed dividers, then check that the lid sits evenly on all four corners. Wood glue in the joints is optional.
Making it personal
Sand everything smooth and finish with food-safe oil. The lid is where decoration belongs: engrave a family name, a monogram or a simple pattern yourself before cutting it out. Filled with a cutlery set, the box is a classic wedding gift, and a plain version works as a tidy storage chest for party or holiday cutlery that only comes out a few times a year.
Questions about this file
Is the lid hinged?
No, it is a separate flat panel that sits on top of the walls. Lift it off to reach the cutlery.
Will the lid slide around on top?
It matches the outer size of the box, so it lines up with the walls. For a snug fit you can glue a thin strip under the lid edges to act as a small lip.
Which thickness should I use for the lid?
4 or 5 mm plywood keeps a lid of this size flat. If you cut 3 mm, oil both faces evenly to reduce warping.
Is there room for artwork on top of this cutlery box?
Yes. The file only has cut lines, so add your own artwork as an engrave layer on the lid in your laser software.
Can the box live in a damp kitchen?
Seal all faces with oil or lacquer and keep it away from the sink splash zone, and it will hold up well in normal kitchen humidity.
Similar files



