VisualizationSliding Lid Coffee Box SVG, Coffee Pod Storage Laser Cut File, Wooden Capsule Box With Lid DXF
A free laser cut file for a wooden coffee box with a sliding lid and three compartments for pods, drip coffee bags and sugar sticks. The SVG and DXF files come in versions for 3, 4, 5 and 6 mm plywood; the box is 280 × 160 × 80 mm (11.02 × 6.30 × 3.15 in) and has 10 pieces, including the lid and two rails. Everything assembles with tabs and slots, and the lid slides along the rails without any hinge or lock.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 160 × 80 mm (11.02 × 6.30 × 3.15 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 926 × 416 mm
- Cut length
- 7.15 m
- Est. time, 10 W diode (3 mm)
- 23 min 50 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 56 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the SVG or DXF for your sheet thickness and test-cut one rail and one slot to check the fit.
- 02Cut all 10 pieces; if you split the 926 mm layout, keep the lid in one piece on a single sheet.
- 03Set the two dividers into the base, add the walls with the shorter front, fit the rails, then slide the lid in to check it runs freely.
- 04Wax the lid edges, finish the outside with oil or lacquer, and fill the three sections.
Half open, half closed
A sliding lid has one handy trick: leave it pushed part of the way and the box works like an open tray, while the rest stays covered. The photo shows exactly that. The lid sits over the right-hand section, and the left side is open to a heap of espresso capsules in gold, purple and bronze. Drip coffee sachets fill the middle section, and sugar sticks wait under the lid on the right. Close it fully and dust, crumbs and kitchen grease stay off the contents.
The two dividers are 70.7 mm tall, lower than the 80 mm walls, so the 273 mm lid glides over them, and the front wall is a few millimetres shorter than the back for the same reason. Two thin 157 mm rails guide the lid. There is no hinge and no catch, so the lid slides right out when you want to wash it or swap it for an engraved one.
Cutting notes
The layout for 3 mm plywood is 926 × 416 mm. Split it in two if your machine has a small bed, keeping the lid whole. A 10 W diode gets through the 3 mm file in about 23 min 50 s; a 40 W CO2 takes about 9 min 56 s and a 100 W CO2 about 4 min 46 s.
Fit the rails before the box is closed up, and try the lid before any glue sets so you can nudge a rail if it binds. A rub of paste wax along the lid edges makes it run smoothly.
Make it yours
The lid is a wide, flat panel, which makes it the obvious place for a coffee bean motif or a family name; add your own engraving before cutting. A matching pair, one for coffee and one for tea, makes a tidy housewarming gift, and a café can brand the lid with its logo for a counter display.
Questions about this file
Is there a lock or a hinge on the coffee box?
No. It simply slides along two rails and can be pulled out completely. That keeps the box easy to clean and lets you leave it partly open on the counter.
How big are the three sections?
Two dividers split the 280 mm length into three similar sections, each running the 160 mm depth of the box. That suits espresso capsules, standing drip bags and sugar or creamer sticks.
My lid feels tight. What can I change?
Sand the lid edges lightly or rub them with wax. If your plywood is thicker than its label says, try the file for the next thickness up.
Is MDF a good choice for this coffee box?
MDF cuts cleanly, but its edges swell if they get wet. Seal it well, or use birch plywood for a box that lives next to the coffee machine.
Can I resize the box to fit a drawer?
Yes, but resizing changes the slot widths as well. Scale the drawing, then correct every slot to your material thickness so the joints still fit.
Similar files



