VisualizationCoffee Pod Storage Bin SVG, Open Capsule Box Laser Cut File, Three Compartment Coffee Organizer DXF
A free laser cut file for an open coffee pod bin with straight 80 mm walls and three deep bays for bulk capsules, drip coffee bags and sugar sticks. It comes as SVG and DXF for 3, 4, 5 and 6 mm plywood, measures 260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in) and is made of 7 pieces. The two dividers slot into the base and walls, and the whole bin holds together with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 180 × 80 mm (10.24 × 7.09 × 3.15 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 900 × 272 mm
- Cut length
- 5.90 m
- Est. time, 10 W diode (3 mm)
- 19 min 39 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 11 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file that matches your plywood and cut one divider to test it in a base slot.
- 02Cut the 7 pieces; split the 900 mm layout across two sheets if your bed is short.
- 03Stand the two dividers in the base, fit the long front and back, then lock everything with the two end panels.
- 04Lacquer the bin inside and out, let it cure, and fill the three bays from your bulk packs.
Built for bulk
Capsules bought in boxes of fifty need somewhere to go. This open bin has four straight walls, all 80 mm tall, and two full-height dividers, so each bay is a deep, square-sided well rather than a shallow tray. The photo shows how much it swallows: the left bay is piled high with copper and gold capsules, the middle one holds a long file of kraft drip coffee bags, and the right bay keeps a bundle of sugar sticks on end.
With 180 mm of depth there is room for sachets to stand in two rows if you like, and nothing spills over the front when the bin is full to the brim. The straight walls also mean several bins line up neatly side by side on a shelf.
Cutting and assembly
Seven parts only: front, back, two ends, base and two dividers. The 3 mm layout is 900 × 272 mm, so on a smaller bed split it between two sheets. Cutting time for the 3 mm file is about 19 min 39 s on a 10 W diode, about 8 min 11 s on a 40 W CO2 and about 3 min 56 s on a 100 W CO2. For 5 or 6 mm plywood a 10 W diode needs several passes, and a CO2 is the faster choice.
Set the dividers into the base, slide the front and back over their tabs, and lock it with the two ends. A little glue in the corner joints keeps the bin square when it is loaded with heavy pods.
Office kitchens and refill stations
This is a practical piece for a shared office kitchen: top it up from the bulk carton and let everyone help themselves. Make two, one for regular and one for decaf. A clear lacquer finish copes with wet hands and spilled coffee, and the plain front panel takes an engraved label if you add one yourself.
Questions about this file
How many capsules does one bay hold?
Each bay is about a third of the 260 mm length, 180 mm deep and 80 mm tall, so it takes a couple of dozen small espresso capsules piled loosely. Larger pods fit in smaller numbers.
How is this different from a sloped coffee tray?
Here every wall is the same 80 mm height, so the bays hold more and the bin lines up flush with others. A sloped tray shows its contents better but holds less.
Does the bin come with a lid?
No, this file is an open bin. If you want a closed box, look at the lidded coffee boxes in the same category.
Can I resize the bin for a deeper drawer?
Change the outline if you need to, but keep every slot equal to your plywood thickness. Scaling the whole drawing would make the slots too wide or too narrow.
Is bare plywood fine next to coffee?
Capsules and sachets are sealed, so plain birch is fine. A food-safe oil or lacquer stops spills from staining the wood.
Similar files



